Cutting With Abrasive Cut-Off Machine; Removing The Workpiece; Tips For Using Abrasive Cut-Off Machine; Transporting The Cut-Off Machine - RIDGID CM1450 Manual Del Usuario

CM1450 14" Abrasive Cut-Off Machine
• Keep the cut-off piece free to move sideways after it is
cut off. Otherwise, it could get wedged against the cut-
off wheel and could be thrown violently.
• Clear everything except the workpiece and related
support devices off the table before turning the machine
on.
Use extra caution with large, very small or
WARNING
awkward workpieces:
• Use extra supports (tables, sawhorses, blocks, etc.) for
any workpieces large enough to tip when not held
down to the tabletop.
• Never use another person as a substitute for a table
extension, or as additional support for a workpiece
that is longer or wider than the basic cut-off machine
table or to help feed, support or pull the workpiece.
• Do not use this tool to cut pieces too small to let you
easily hold the work with the vise.
• When cutting irregularly shaped workpieces, plan your
work so it will not slip, pinch the cut-off wheel and be
torn from the vise.

Cutting With Abrasive Cut-Off Machine

WARNING
Never cut wood, magnesium, masonry, stone or
ceramic with this tool.
Keep your face and body to one side of the abra-
sive wheel, out of line with possible thrown sparks
or dust.
Do not use any type of cutting lubricant with this
cut-off tool.
1. To start tool, firmly grasp the handle and depress the
trigger switch. Be sure to allow the motor to reach
maximum speed prior to cutting. This will help reduce
the risk of thrown workpieces.
2. When beginning a cut with the tool, care should be
exercised not to bump or slam the wheel into the
work. Once it has entered the workpiece, continue to
cut with an even smooth stroke. Do not apply exces-
sive pressure.
If the wheel is damaged do to misuse, it
WARNING
may develop cracks and eventually shatter without warn-
ing.
NOTE! The faster a cut is made the less heat is creat-
ed in the workpiece, preventing discoloring,
and wheel life is prolonged. Cut with a steady
force without overloading the machine.
3. When the cut is complete, raise the wheel com-
pletely from the workpiece before releasing the trigger
switch and allowing the motor to stop.
WARNING
trigger switch immediately and wait for all moving parts to
stop. Unplug cut-off machine before attempting to remove
the material.
Removing Workpiece
1. Turn the vice handle counterclockwise to release
the workpiece. Raise the quick release lever and
pull back on the handle to allow the workpiece to be
easily removed from the vise.
2. Slide the workpiece out of the machine keeping a firm
grip on the workpiece as it clears the machine.
WARNING
ment tip-overs when handling long workpieces, make
sure that the end farthest from the unit is supported prior
to removal.
Tips For Using Abrasive Cut-Off
Machine
Life of the abrasive wheel will depend on proper use of the
cut-off machine. Procedures that should be followed are
as follows:
• Do not "jam" the abrasive wheel into the work or
apply excessive pressure while using this
machine.
• Let the machine reach full speed before starting to
cut.
• Only cut the type and size of material specified for
this machine.
• Do not grind against the side of the wheel.
• Clamp the material correctly and ensure that it is
center relative to the abrasive wheel.

Transporting The Cut-Off Machine

Before moving this tool, lock the power head in the lower
position using the chain (Figure 1). Check to ensure the
machine is unplugged from the power source.
Lift the machine by using the hand-hold areas in each side
of bottom of the base or by the carrying handle (Figure 1).
Use proper lifting technique. Bend your knees so you
can lift with your legs, not your back. Hold the tool close to
your body when lifting.
Never carry tool by the power cord or the trigger grip of
the plastic handle. Carrying the tool by the power cord
could result in damage to the cord resulting in electrical
shock or fire.
Ridge Tool Company
If material becomes jammed, release the
To avoid injury from falling parts or equip-
9