Input Switching; Size Switching - Yamaha PDM-4220 Manual Del Usuario

OPERATING INSTRUCTIONS (continued)
CHANNEL UP/DOWN buttons

Input Switching

• Input can be switched by pressing the AV1~6, RGB1 or
RGB2 buttons of the remote control.
• Input can be switched to TV by pressing CHANNEL UP/
DOWN buttons or PROGRAM SELECT buttons.
• Input can be switched in the sequence of TV ➝ AV1 ➝
AV2 ➝ AV3 ➝ AV4 ➝ AV5 ➝ AV6 ➝ RGB1 ➝ RGB2 by
pressing the INPUT SELECT button of the control
panel.
TV AV1 AV2
RGB2 RGB1

Size Switching

Each time the ZOOM button of the remote control is
pressed, the screen display size will change in sequence
and the status will be displayed at the bottom of the
screen.
• During TV/VIDEO signal input (AV4, AV5, AV6, RGB1
(set to [DVI-STB]) and RGB2 (set to [Component])
Panoramic 4:3
14:9Zoom C14:9L
• The size will fix as Full mode and not change when receiving
the component signal of 1080i/50, 1080i/60, 720p/50 or 720p/60.
Full
Display size selection diagram
When you want to
Play a 4:3 image in a 16:9 screen faithfully.
Play a 4:3 image in a 16:9 screen with the
height and width of the middle of the
screen enlarged on equal scales and with
both sides appearing somewhat enlarged.
Play a 16:9 VISTA size image from a 4:3
image faithfully reproduced on the 16:9
screen.
Play a 4:3 image faithfully in a 16:9 screen
in the standard vertical size and
horizontally squeezed.*
INPUT SELECT button
AV3 AV4
AV6 AV5
Full
Zoom
Set the display size Input signal
4 : 3
Panoramic
(4.:3 signal)
Zoom
Full
(Squeeze)
STANDBY/ON
INPUT SELECT
buttons
ZOOM button
• During AV1~ AV3 signal input
Auto
14:9Zoom
• [Auto] is the mode using the Switch signal from the equipment
connected to AV1~AV3 terminal included in SCART connector
No.8 pin which indicate the picture format of the video source.
When Switch signal has not been detected, Default Zoom setting
in the Function Menu is used to choose.
• During TV mode
Auto
14:9Zoom
• [Auto] is the mode using WSS (Wide Screen Signals) which
identify the picture format movies and programs are broadcast in.
Various broadcast stations now transmit WSS. It can be detected
and the monitor automatically switch to the correct format.
However, some broadcasters do not transmit WSS, so this monitor
will not recognize which format is being transmitted. Therefore,
Default Zoom setting in the Function Menu is used to choose when
a WSS has not been sent or has not been detected.
Display screen
(Vista)
RECALL
TV DVD
RECALL button
i +
/I
AV 1 AV 2 AV 3 AV 4
AV 5 AV 6 RGB 1 RGB 2
1 2 3
PROGRAM
4 5 6
SELECT button
7 8 9
0
2-4-12
MENU RETURN
OK
A. MODE P. MODE
VOL PROG
+
+
P
CHANNEL
UP/DOWN buttons
I/II P
?
i
Full Zoom
C14:9L
Full Zoom
C14:9L
Remarks
Blanking occurs on both sides.
• The 4:3 image is called a letterbox image.
• In some cases, some slight blanking
may remain at the top and bottom.
* An image with an aspect ratio of 16:9
shrunk horizontally to 4:3 to display in a
4:3 screen
19