Milwaukee 6955-20 Manual Del Operador página 8

Adjusting the Kerf Plates
Kerf plates reduce tear-out and splintering along
the cut by providing edge support. Because blades
vary in width, adjust the kerf plates with every blade
change.
Never make a cut without the adjustable kerf plates
installed. The kerf plates can be set at their maximum
width to accommodate all blade widths and bevel
angles if tear-out and splintering are not a concern.
1. Unplug the tool.
2. Install the blade to be used. Each time the blade
is changed, check to be sure the kerf plates are
adjusted properly.
3. Set the bevel angle. Each time the bevel is
changed, check to be sure the kerf plates are
adjusted properly.
4. Loosen the six kerf plate adjusting screws.
5. Lower the saw head to the full depth of cut (the
point where the saw head will not lower any fur-
ther).
6. Slide the kerf plates to the desired spacing and
tighten the six screws.
7. Check to be sure the saw blade does not contact
the kerf plates before starting the saw.
OPERATION
To reduce the risk of injury, wear
WARNING
safety goggles or glasses with side
shields. Always wait for the blade to stop com-
pletely and unplug the tool before changing ac-
cessories or making adjustments. Do not defeat
the guards.
Using Face Boards
(Zero Clearance Sub Fences)
There are face board mounting holes in the fences for
attaching face boards. Face boards place distance
between the fence and the workpiece, providing
improved support for some workpieces. Workpiece
splintering can be reduced by using face boards. As
the width of the face board increases, the height of
the workpiece which can be cut increases slightly
(but the width capacity decreases slightly). Similarly,
if you place a face board on the saw table and place
a workpiece on top of the face board, you can cut a
workpiece with greater width (but with less height).
The tool is shipped with both the upper and lower
guard installed. The lower guard should cover the
blade when the saw head is up and it should move
freely and open automatically as the saw head is
lowered into the workpiece. If the lower guard appears
loose, sticks, or if it does not move to cover the blade
when the saw head is up, tighten the guard bracket
screws. If it still does not move freely, take the saw
to an authorized service center for repairs. Do not
attempt to open the guard further than the automatic
action permits.
Select the Workpiece Carefully
Be cautious of pitchy, knotty, wet or warped work-
pieces. These materials are likely to create pinching
conditions. Workpieces that bow and pinch may
result in kick back. Inspect for and remove nails
before cutting. Always keep blades clean and sharp;
otherwise the blade produces a narrow kerf and is
likely to be pinched by the workpiece. This tool is
not recommended for cutting ferrous metals such as
iron and steel. See Applications for a more complete
list of materials.
Guards
Support the Workpiece Properly
Always support the workpiece during operation. Oth-
erwise, the workpiece may pull up and into the saw.
1. Use the Fence: Align the workpiece flush against
the fence to provide a straight path for the saw
blade. This will help eliminate the tendency for the
blade teeth to bind. The fence can be used as a
support for miter, bevel and compound cuts.
2. Use a clamp: Clamp the workpiece to the fence
or base with a C-clamp.
Support of Longer Workpieces
Longer workpieces need support along their full
length. If you are using the saw on a level work
bench, prop up the workpiece to a height of 4-3/4"
from the bottom of the saw feet. There are also many
aftermarket work tables specifically designed for miter
saws that provide supports for all types of workpieces.
Adjusting the Miter Angle
The miter angle can be set using detents for commonly
cut angles, as well as finely adjusted to any angle. Use
the miter angle pointer to adjust the turntable to any
whole degree across the miter range. The digital miter
angle readout shows the selected angle.
1. Loosen the miter angle lock knob.
2. To set the miter angle, pull up on the detent lever
and rotate the turntable to the detent angle closest
to the desired angle. The saw cuts miter angles
from 55° on the left to 60° on the right. Detents are
available at 0°, 15°, 22.5° 31.62°, 45°, and 60°.
3. Tighten the miter angle lock knob to use the miter
angle set at the detent before making a cut.
4. To make a fine adjustment to the miter angle:
A. Pull up and hold the detent lever .
B. Push the fine adjustment ring forward until it
locks to engage override.
C. Rotate the fine adjustment ring left or right until
the desired angle is displayed on the digital
miter angle readout. ¼ turn = 1° change in miter
angle.
D. Tighten the miter angle lock knob to secure the
table before making a cut.
E. Pull up on the detent lever to release the fine
adjustment ring.
A
Adjusting the Bevel Angle
The bevel angle can be set using detents for commonly
cut angles, as well as adjusted to any angle in between
by using the bevel angle scale. The bevel mechanism
also has several degrees of overtravel on both the left
and right.
1. Unplug the tool.
2. To adjust the bevel angle, place one hand on the
front handle for better control.
3. Using the other hand, lift the bevel adjustment
lever:
8
B
D
C
E