Possible Causes Of Operation Problems And Their Removal; Liquidation Of Transporting Packing, Liquidation Of The Product After The Lapse Of Service Life - Viadrus AGURO Manual Del Usuario

8

Possible causes of operation problems and their removal

In case of problems that you cannot remove by yourselves, contact the supplier of the stove or a chimney-sweeper.
PROBLÉM CAUSE
Functionless display
The equipment is not powered
The stove cannot be The equipment is not powered
„started", the display
doesn't light
The stove cannot be
„started", the display Low pressure to the display
lights
An obstacle in the chimney
Impacted or closed central air
supply
Insufficient draught in the
Too strong draught of the fume
stove after installation.
hood
Functionless exhaust fan
Wet fuel
Low pressure in the room
Impacted central air supply
The central air supply can be fully
or partially blocked
The fire is hardly kindled
and after a short time The chimney shutter is blocked by
burned out soot
The stove is sooted
Low draught of the chimney
Functionless exhaust fan
Wet fuel
The stove wasn't enough warmed
Glass fumigation and up
blackening
Leaky door
Functionless exhaust fan
Backward chimney draught as a
result of atmospheric conditions
Smoke smell near the The door is not fully closed or
stove leaky
Functionless exhaust fan
Neglect of check and cleaning
Fuel fire penetration to the
reservoir
Defect temperature sensor in the
reservoir
Neglect of check and cleaning,
The fire in the chimney
heating by wet wood
9 Liquidation of transporting packing, liquidation of the product after
the lapse of service life
Cardboard cover
Plastic package
Metal tightening band
Ceramic glass
Gasket
SOLUTION
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
sorted communal waste
sorted communal waste
collecting center of metal waste
collecting center for glass
mixed communal waste
95
Switch-on the switch situated on the rear side to the position „1"
Check that the power supply cord is properly inserted
Switch-on the switch situated on the rear side to the position „1"
Check that the power supply cord is properly inserted
Hold the button ON/OFF for appr. 3 sec.
Press more or several times to the display
Replace the battery in the remote control panel
Check the chimney
Check the central air supply
Check that the central air supply is opened
Connect the suction of combustion air to the central air supply
Correct a mode of the fume hood, decrease draught
Check functionality of the fan
In case of inactivity, call service
Burn by dry pellets, see chapter 5.3.
Open the window near the stove for several minutes
Check that the central air supply is opened
Disconnect the central air supply and try to burn the fire only with
help of air in the room
Check that the central air supply is opened
Check and clean the chimney shutter
Perform maintenance, see chapter 7
Check the chimney
Switch off the fume hood
Check functionality of the fan
In case of inactivity, call service
Burn by dry pellets, see chapter 5.3.
Warm up the stove to the operation temperature
Replace the door sealing
Check functionality of the fan
In case of inactivity, call service
Wait for better weather
Close properly the door
Replace the door sealing
Check functionality of the fan
In case of inactivity, call service
In no case extinguish by water
Close all air supplies for combustion, and, if possible, cover up the
chimney
Contact the seller for inspection of the consumer
Call service
In no cases extinguish by water
Close all air supplies for combustion, and, if it is possible, cover up
the chimney
Contact a chimney-sweeper service to assess the state of the
chimney after the fire
Contact the manufacturer to inspect the consumer
GB
GB