albatros ACTPL-S Manual De Uso página 14

Operating Instructions
5
Operation:
When the tub is switched on, only the two
level indicator LEDs (L1 and L2) will be lit. The
WHIRLPOOL and AIRPOOL hydromassage
systems can be operated either independently
or simultaneously.
Here is an example of how to operate the
system.
First, fi ll the tub with lukewarm water.
In order to switch on the WHIRLPOOL function
at full power, the AIRPOOL function at medium
power, and the OZONE function at maximum
power, proceed as follows: press and hold down
the WHIRLPOOL key for maximum power; press
and hold down the AIRPOOL KEY so that the
function starts at maximum power; then briefl y
press the AIRPOOL key once to reduce the
power to medium; then press and hold down
the OZONE key to start the OZONE function at
maximum intensity.
20'
Timer
The hydromassage tub is fi tted with a timer
which automatically interrupts operation of the
hydromassage system after 20 minutes
6
Filling the disinfectant reservoir
To fi ll the disinfectant reservoir, remove the fi ller
cap located on the edge of the tub, and introduce
1 litre of disinfectant (pilot light L2 on the keyboard
will change from red to green).
Led 2
Each disinfection cycle requires approximately
70 g of disinfectant solution (this quantity cannot
be modifi ed). The capacity of the reservoir is
therefore suffi cient for about 12 disinfection
cycles.
A level sensor inside the reservoir checks for the
presence of disinfectant; if the reservoir is empty,
the disinfection cycle will not start.
The recommended disinfectant solution, which
is available through our authorized dealers and
Service Centres, not only sanitizes the appliance,
but also prevents fermentation and unpleasant
odours, and inhibits the formation of algae and
mildew.
IMPORTANT!
Do not use products containing chlorine
(Amuchina, Bleach etc.) as these may
damage the system and cause leakage of
disinfectant.
7
Disinfection cycle
Tubs fi tted with this type of keyboard may feature
the System Clean or Professional disinfection
system.
Whichever of the two systems is featured, the
disinfection cycle is an essential function which
guarantees the maximum hygiene and correct
operation of the appliance, since it disinfects
those parts of the system that cannot be reached
during normal cleaning.
With the System Clean disinfection system, the
water used for the hydromassage can be used.
The cycle can only be started when the tub is
fi lled with water.
For the Professional disinfection cycle, the tub
must be empty, since this system uses water
directly from the domestic water supply, and
mixes the water with the disinfectant to fl ush the
hydromassage circuit.
Important:
Before starting the disinfection cycle - whether
System Clean or Professional - ensure that the
tub is not in use.
Also ensure that all the hydromassage nozzles
are open.
The disinfection cycle lasts for about two minutes
and, once started, cannot be interrupted.
Starting the disinfection cycle
Before starting the disinfection cycle, ensure
that:
1) The main power switch is set to "ON".
2) For System Clean disinfection, the level of
Led 1
Led 1
3) For ACTPLR-S and ACTPLR-P only:
N.B.: This starting procedure is designed to
act as a safety feature to prevent the user from
inadvertently starting the disinfection cycle.
Once the cycle has started, the tub returns
to standy-by mode and all the LEDs (with the
exception of LEDs L1 and L2) will switch off).
Manuale Uso VS ACTPL-S/ACTPL-P - Code 10009717 - Edition 2 - 06/2007
3
water in the tub must be 5 cm above the
hydromassage nozzles (pilot light L1 on the
keyboard lights GREEN).
For the Professional disinfection system,
check that the tub is empty (pilot light L1 on
the keyboard lights RED).
To start the disinfection cycle, press the
LYMPH DRAINAGE and CYCLICAL keys
simultaneously, holding them down for about
3 seconds. The key will begin to fl ash and
an acoustic signal will sound for the entire
duration of the cycle to warn the user that
the disinfection cycle is in operation.
For ACTPUL-S and ACTPUL-P only:
Press this key for about 3 seconds to start
the disinfection cycle
The key will begin to fl ash and an acoustic
signal will sound for the entire duration of the
cycle to warn the user that the disinfection
cycle is in operation.
English