Clean Rinse (Optional); Water Cleaning And Water Handling (Optional) - Hedson W10 Manual Del Usuario

The QuickLift is designed for both lifting the wheel into the
machine and lowering the wheel back down on the floor. Users
who want to bounce the wheels back down on the floor should
close the plate before doing this. Bouncing heavy wheels on
the plate might deform it.
Before using the QuickLift, read these instructions carefully.
1. Installation
When the machine is installed (see chapter 6), the lift plate
must be correctly adjusted. This can't be factory set, since most
shop floors are not level. Ignoring adjusting the lift will void the
warranty. Not adjusting the lift before use may cause damages
to the floor from the plate being dragged along the floor, or
damages to the lift from dropping wheels on it.
Unfold the lift plate by pulling the sprint on the bottom right
side. Adjust the opening angle of the plate by moving the
eccentric washer on the bottom left side up or down. The plate
should touch the floor, but should separate from the floor as
soon as the lift starts moving. If the eccentric washer doesn't
have enough travel, it could be turned up-side-down or front-
to-back.
Tighten the bolts after a good position of the plate is found.
Re-inspect the position of the lift plate after some usage to
make sure it instantly separates from the floor during operation.
2. Operation
Pull the knob to the right of the lift plate and fold it out with
your hand. Do not release it until it has touched the floor. In
precipitated position, the knob will automatically spring back
and work as a stop for accidentally closing the plate in upward
position. Closing the plate requires pulling the knob at the
same time.
Place the wheel on the lift plate and activate the lift by turning
the knob on the front panel to the left. The knob must be in
this position during the whole lifting process. The lift is weight
sensitive, this means it will lift heavier wheels that are standing
more stable on the plate faster (approximately 2-3 seconds).
Smaller and lighter wheels will be lifted slower, in
approximately 4 seconds. If faster lifting time for smaller wheels
is desired, the wheel can be pushed against the lift plate by the
operator during the start of the lift cycle.
The lift plate can be left in its upper position during washing,
and the wheel could then be lowered back on the ground using
the lift.
PLEASE NOTE: When lift plate is folded out and ready
to use for lifting, wheels should not be taken out of
the machine by bouncing them on the lift plate. Heavy
wheels will deform the lift plate.
230312-EN rev.5 2016-09-21
W10 & W12
16. CLEAN RINSE
The W10 and W12 can be equipped with an extra cleaning
feature, rinsing the wheels with clean tap water after finished
wash cycle and before blowing starts.
If the Clean Rinse option is being used in the machine, the
water change intervals may be increased to approximately 400
washes.
Contact your local sales rep. for more information.
17. WATER CLEANING AND WATER
HANDLING
The dirt on the wheels that are washed in a Hedson wheel
washer is the dirt from our roads and cars. This dirt might
also contain heavy metal residuals, especially copper from the
brakes, zinc and nickel. The permitted limit values differ locally.
Please contact your local water authority about the handling of
the waste water.
The waste water from this machine should be let out through
an oil separator. If required, the machine can be equipped with
an environmentally friendly water cleaning and filtering system.
Hedson Technologies AB has developed an easy and effective
waste water cleaning method. The method consists of a
coagulation powder (art.no. 12076) that is added into the
machine while stirring the water. The coagulation powder binds
the heavy metal particles through flocculation and these bigger
particles can be filtered away (art.no. 12037 hose filter and
art.no. 12038 basket filter). The purified water fulfils all limit
values and authority requirements.
When using equipment that handles warm water, there is a
risk of harmful bacterium emerging (water- and/or airborne
diffusion), especially if the water has been left non-operative
in the machine for a while. We therefore recommend the
following procedures:
• By adding a bactericide to the water in the washing
compartment (art.no. 230521, 2 litre per 300 litre water)
• To empty out the water of the machine when not using it.
PLEASE NOTE: BIO-291 or any other detergent must
not be used in the machine when using the Hedson
water cleaning method!
Contact your local sales rep. for information.
(OPTIONAL)
(OPTIONAL)
13