Technical Data; Before Starting The Equipment - Hurricane MS 1235/2 Manual De Instrucciones

Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 85
Anleitung_MS_1235_2_SPK7__ 19.11.15 07:43 Seite 21

4. Technical data

Engine displacement
Maximum engine capacity
Bar length
Cutter rail length
Chain pitch
Chain thickness
Idling speed
Maximum speed with cutting equipment
Chain speed max.
Tank capacity
Oil tank capacity
Anti-vibration function
Chain wheel teeth
Chain brake
Clutch
Automatic chain lubrication
Low-kickback chain
Net weight without chain and chain bar
Net weight (dry)
Fuel consumption (specific)
LPA sound pressure level (ISO 22868)
KPA uncertainty
LWA sound power level measured
(ISO 22868)
KWA uncertainty
LWA sound power level guaranteed
(ISO 2000/14/EC)
Ahv vibration (front handle)
(ISO 22867)
Khv uncertainty
Ahv vibration (rear handle)
(ISO 22867)
Khv uncertainty
Chain type
Bar type
Spark plug
37.2 cm
3
1.2 kW
33 cm
14" (35.56 cm)
(0.375"), 9,525 mm
(0.05"), 1.27 mm
3100 ± 300 rpm
12000 rpm
22,9 m/s
310 cm
3
210 cm
3
Yes
6 teeth x 9.525 mm
Yes
Yes
Yes
Yes
4.5 kg
5 kg
500 g / kWh
98.9 dB(A)
3 dB(A)
107.8 dB(A)
3 dB(A)
114 dB(A)
max. 6.74 m/s
2
1.5 m/s
2
max. 5.53 m/s
2
1.5 m/s
2
OREGON 91P053X
OREGON 140SCEA041
NHSP LD L8RTF
Keep the noise emissions and vibrations to a
minimum.
Only use appliances which are in perfect working
n
order.
Service and clean the appliance regularly.
n
Adapt your working style to suit the appliance.
n
Do not overload the appliance.
n
Have the appliance serviced whenever
n
necessary.
Switch the appliance off when it is not in use.
n
Wear protective gloves.
n

5. Before starting the equipment

Important: Do not start the engine until the saw
is fully assembled.
Important: Wear protective gloves at all times
when handling the chain.
5.1 Fit the chain bar
To ensure that the bar and the chain are supplied
with oil, USE ONLY THE ORIGINAL BAR. The oiling
hole (Fig. 2/Item A) must be kept clear of dirt and any
build-up of residue.
1. Make sure the Chain brake lever is pulled back
into the DISENGAGED position (Fig. 3A)
2. Remove the two bar fastening nuts (B). Remove
the cover (Fig. 3B).
3. Using a screwdriver, run the adjustment screw (D)
COUNTERCLOCKWISE until the TANG (E)
(projecting prong) is to the end of its travel toward
the clutch drum and sprocket (Fig. 3B/3C).
4. Fit the open end of the chain bar over the die bar
pins (F) (Fig. 3C/3D).
5.2 To install saw chain
1. Spread chain out in a loop with cutting edges (A)
pointing CLOCKWISE around loop (Fig. 4A).
2. Slip the chain around the sprocket (B) behind the
clutch (C). Make sure the links fit between the
sprocket teeth (Fig. 4B).
3. Guide the drive links into the groove (D) and
around the end of the bar (Fig. 4B).
NOTE: The saw chain may droop slightly on the lower
part of bar. This is normal.
4. Pull the chain bar forward until the chain is closely
seated. Make sure that all the drive links are in the
groove of the bar.
5. Fit the clutch cover and fasten it with 2 screws.
Make sure that the pivot (Fig. 3C/Item E) fits into
the chain bar (Fig. 3D/Item G). The chain must
GB
21

Hide quick links:

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

45.016.45

Tabla de contenido