Peg-Perego Pliko P3 Modular System On Track Instrucciones De Uso página 25

weighing more than 0,5 Kg (1 lbs).
BRAKES
11• To set the brakes on Pliko P3, lower the lever on the rear
wheels with your foot, as shown in the figure.
• To release the brakes, lift the lever.
• Always set the brakes when the stroller is not moving.
SWIVEL WHEELS
12• To swivel the front wheels, lower the lever as shown in figure
A. To set the wheels on stationary, lift the lever as shown in
figure B.
ADJUSTING THE HANDLEBARS
13• The height of the handlebars can be adjusted to two
positions. For the higher position, press the button while
pulling the handlebar upward. To lower the handlebar, press
the button and push the handlebar downward.
FOLDING UP PLIKO P3
• Before folding up Pliko P3, remove the Navetta bassinet
unit or Primo Viaggio car seat.
14• The stroller can be folded up using one hand only. Pull first
one lever upwards and then the other, until they click.
15• Grab the central handlebar (Figure 3) and pull upward until
the stroller folds up, as shown in the figure.
16• Check to make sure that the safety hook is fastened. The
folded stroller will stand upright.
CARRYING
17• Pliko P3 can be conveniently carried (with the front wheels set
on stationary) when held by the central handle, as shown in
the figure.
18• The side handle can also be used to carry the stroller, as
shown in the figure.
THE GANCIOMATIC SYSTEM with
THE PLIKO P3 CHASSIS
The Ganciomatic system is a practical, fast way to fasten the
Navetta bassinet unit and the Primo Viaggio car seat – which are
both equipped with the Ganciomatic system - to the Pliko P3
chassis, using the Ganciomatic hooks.
GANCIOMATIC HOOKS ON THE CHASSIS
19• To raise the Ganciomatic hooks on the chassis, turn them
upwards until they click into place, as shown in the figure.
20• To lower the Ganciomatic hooks on the chassis, pull the lever
outwards while turning the hooks downwards, as shown in
the figure.
PLIKO P3 + NAVETTA
To fasten the Navetta bassinet unit to the Pliko P3 chassis, first:
- Set the brakes on the Pliko P3;
- Raise the Ganciomatic hooks;
21• Turn the two levers on the rear of the chassis outwards, as
shown in the figure;
22• Lift the chassis footboard to its highest position (Figure 1);
23• The Pliko P3 chassis is now ready for attaching the Navetta
bassinet unit;
24• Hold the Navetta bassinet unit by its handle, and place it on
the Ganciomatic hooks on the chassis, keeping the head
of the bassinet unit on the opposite side from the chassis
handlebars.
- Press down with both hands on the sides of the Navetta
bassinet unit, until it clicks into place.
- To remove the Navetta bassinet unit from the chassis, consult
the instruction manual.
PLIKO P3 + PRIMO VIAGGIO
To fasten the Primo Viaggio car seat to the Pliko P3 chassis, first:
- Set the brakes on the Pliko P3;
- Attach the front bar (see the "Front Bar" section below).
25• The Pliko P3 chassis is now ready for attaching the Primo
Viaggio car seat.
26• Hold the car seat by its handle, and place it on the Ganciomatic
hooks on the chassis, keeping the head of the car seat on the
opposite side from the chassis handlebars. Press down with
both hands on the sides of the car seat, until it clicks into place.
- To remove the car seat from the chassis, consult the
instruction manual.
FRONT BAR
27• The chassis comes with caps closing the ends of the armrests.
To fasten the front bar to the chassis, remove the caps (keep
them for when you want to use the chassis without the
front bar). To remove the caps, press the buttons under the
armrests while pulling the caps off.
28• To fasten the front bar to the chassis, slip the two ends of the
front bar into the armrests as shown in the figure, pressing
until the bar clicks into place.
29• The front bar can be opened on one side only to allow the
child to get in and out of the stroller easier when he or she
is older. To open the front bar, press the button under the
armrest while pulling the front bar outwards.
30• To remove the front bar, press the two buttons under the
armrests while pulling the bar off the chassis.
HOW TO TURN THE CHASSIS INTO A STROLLER
ASSEMBLY
31• To turn the Pliko P3 chassis into a stroller, make sure the two
levers are lowered as shown in the figure.
32• Place the backrest with the sack on the seat of the chassis, as
shown in the figure.
33• To fasten the backrest to the chassis, insert the two ends of
the backrest into the seat of the chassis while pressing the
two buttons, as shown in Figure 1. Press on the backrest until
it clicks into place, as shown in Figure 2.
34• To attach the backrest adjustor to the chassis, turn the
fastener upward (Figure B – turn in the direction shown by
the arrow), placing it behind the rear brace.
35• Push the two fasteners downward until they click into place
on the braces.
36• To line the stroller, fasten the sack to the armrests as shown by
the arrows in the figure.
37• Insert the footboard levers into the sack on the backrest, as
shown in the figure.
38• Finally, fasten the buttons on the sack at the bottom, as
shown in Figure A. Pass the lower leg divider belt under the
seat, as shown in Figure B, and leave the upper leg divider
over the sack.
OPENING AND FOLDING UP
• To open the Pliko P3 stroller, repeat the steps shown in
Figures 2 and 3.
• To fold up the Pliko P3 stroller, loosen the hood braces, lift the
backrest, and repeat the steps shown in Figures 14, 15, and 16.
ADJUSTING THE FOOTBOARD
39• The footboard can be adjusted to three positions. To lower
the footboard, pull the two side levers downwards. To lift the
footboard, pull it upwards until it clicks into place.
REAR FOOTBOARD
40• The rear footboard helps the mother to push the stroller over
small bumps, and can be used to carry a second child.
LOADING
41• To use the Pliko P3 with two children, first set the brakes on
the stroller. Next place the smaller child in the seat and fasten
the safety belt (1). Hold the handlebars (2) and have the
second child stand on the rear footboard (3).
• Never leave your children alone in the stroller.
• Do not allow a child to stand on the rear footboard when
the stroller is empty.
HOOD
• The hood can be used with the Navetta bassinet unit and can
be fastened to both the Navetta bassinet unit and the stroller.
It is equipped with a zipper to attach the rain canopy.
42• To assemble the hood onto the Navetta bassinet unit
unbutton buttons A and B (figure 1). Fasten the hood as
indicated in figure 2 and make sure it is fastened properly,
figure 3.
43• To assemble the hood onto the stroller fasten it as indicated