Troubleshooting - Toyotomi TAD-35K Manual De Instrucciones

8. TROUBLESHOOTING

SYMPTOM CAUSE
Unit does not
- Power cut.
work.
- T h e p l u g h a s b e e n
plugged improperly.
- The full-tank indicator
is ON. Tank is full.
Unit suddenly
- The indoor temperature
stops during
has reached the set
in operation.
temperature level.
- The preset time is up.
- The full-tank indicator
is ON. Tank is full.
Unit runs in-
- Malfunction.
termittently.
- Surrounding tempera-
ture is too high or too
low.
- Exhaust duct hose is
blocked.
Unit func-
- Window or door is left
tions but the
open in the room.
room is not
- There is heat source in
cooled.
the room or too many
of people in it.
- A i r i n t a k e g r i l l e i s
clogged.
- Filter is too dirty.
- Temperature setting is
too high.
Condensed
- The tank is nearly full.
water is
spilled out
when moving
the unit.
LCD display - The temperature sen-
shows "E1". sor error
LCD display - The coil sensor error
shows "E2".
BEFORE CALLING FOR SERVICE
The followings are not defects.
A hissing noise or hollow

sound :

A squeaking noise :

Odor :
The unit does not start nor

change operation mode im-
mediately :
SOLUTION
- Wait for power to be
supplied again.
- Plug in again.
- Remove the drain wa-
ter from the drain tank.
- Reset the temperature
level.
- Reset the timer.
- Remove the drain wa-
ter from the drain tank.
- Contact your dealer.
- Check the duct hose.
- Close all windows and
door.
- M o v e o u t a n y h e a t
source in the room.
- Clean the air intake
grille.
- Replace the filter.
- Lower the temperature
setting.
- Remove the drain plug
on the rear bottom of
the unit, drain off the
water then the unit will
be in operation auto-
matically.
- Contact your dealer.
- Contact your dealer.
This sound is generated from the
refrigerant flowing within pipes.
This noise is generated from the
unit when it is expands or con-
tracts with temperature changes.
Such odor as tobacco, cosmetics,
or foods may accumulate in the
unit.
To prevent overloading the com-
pressor motor, the unit will be
stopped for more than 3 minutes.
9. SPECIFICATIONS
MODEL
COOLING CAPACITY
DEHUMIDIFYING CAPACITY
(26.7°C / 60%)
POWER SOURCE
POWER CONSUMPTION
OPERATING CURRENT
AIR FLOW (MAX.)
OPERATING TEMP. RANGE
DIMENSIONS (W × H × D)
WEIGHT
COMPRESSOR
REFRIGERANT
NOTE: Cooling air capacity will vary according to temperature and
humidity of the room.
10. VENTING KIT ACCESSORIES
If the unit is to be used exclusively in one space, the cooling effi-
ciency will be enhanced by using the following venting kit accesso-
ries.
EXHAUST DUCT SET (FLEXIBLE TUBE) (Fig. I)
Max. 1.2m (4 ft.)
WINDOW PANEL KIT (Fig. J)
For sliding and double-hung
windows
Max. 94cm (37 in.)
Min. 72cm (28-1/4 in.)
USING EXHAUST DUCT SET (Fig. I)
1. Insert both ends of exhaust duct hose (flexible tube) (I2) into
exhaust duct hose adapter nozzle (I1) by turning it counter
clockwise onto the tube and fix one of the exhaust dust hose
adapter nozzle (I1) into exhaust outlet (B2) by turning it clock-
wise until it locks.
2. Extend the exhaust duct hose (I2) and close the window or
door as far as possible trapping the exhaust duct hose adapt-
er nozzle (I1).
NOTE: Place the unit as close as possible to the window or
door.
USING WINDOW PANEL KIT (Fig. J)
NOTE: Window installations are possible by the use of the
exhaust duct set and window planel kit.
1. Fix the exhaust duct hose grill (J3) to the window panel with
four (4) screws. Make sure that the panel is extended so that
screws do not go into sliding portion of panel.
2. Open the window.
3. Place the window panel in the window, extending it to fit the
width of the window. Once panel is extended, the panel can
be locked into this width by tightening the two (2) screws on
the top panel.
4. Close the window.
5. Attach the exhaust duct hose adapter nozzle (I1) on the ex-
haust duct hose grille (J3).
6. When not in use, the exhaust duct hose adapter nozzle (I1)
may be closed off with the cover (J4) for exhaust duct hose
grille (J3) provided.
NOTE: The same procedure can be adapted for vertical in-
stallation in sliding windows.
3
ENGLISH
TAD-35K
3.5 kW (12,000 BTU / H)
1.8 L/H
Single Phase 220V, 50Hz
1300 W
5.9 A
318 m³/h
16°C-35°C
460 × 742 × 405 mm
32.9 kg
ROTARY
R-410A (560 g)