Safety Notices - Velocity Burning Desire II Instrucciones De Montaje

4. Wirken Männerstimmen aufgebläht, oder der Tiefbass zu schwach,
sollten Sie den LP-FREQ-Regler etwas in Richtung Minimum drehen
und die Abstimmung wieder bei Punkt 2. fortsetzen.
5. Wirkt der Bass tief, aber unsauber und dröhnig oder klingen Männer-
stimmen zu dünn, ist der LP-FREQ-Regler etwas in Richtung Maxi-
mum zu drehen. Außerdem sollten Sie den Phasenregler so einstel-
len, dass der obere Bass möglichst kräftig klingt. Setzen Sie die Ab-
stimmung dann unter Punkt 2. fort.
Zur genauen akustischen Abstimmung der Frequenzweiche empfehlen
wir Ihnen die Beratung durch einen Velocity Fachhändler.
Die technischen Daten der eingesetzten Lautsprecher müssen bei
der Abstimmung der Frequenzweiche unbedingt berücksichtigt
werden.
Bass Boost
Mit Hilfe des Bass Boost Reglers kann die Baßwiedergabe des Veloci-
ty-Verstärkers eingestellt werden. Der Einstellbereich reicht von 0 dB
bis +12 dB.
Subsonic-Filter
Das Subsonic-Filter dient dem Verstärkerbetrieb bei angeschlossenem
Subwoofer. Es kann geregelt werden um den Subwoofer vor mechani-
scher Überlastung durch tiefe nicht mehr in den Hörbereich fallende
Frequenzen zu schützen.
Betriebsanzeige (POWER / PROTECT)
Blaues Licht: Endstufe an, regulärer Betriebszustand.
Rotes Licht: Endstufe ist elektronisch abgeschaltet da Fehlerfall vorliegt.
Änderungen vorbehalten.
Introduction (GB)
Congratulations on purchasing this high-quality car audio subwoofer
amplifier.
As innovators in the world of car hi-fi, we are pleased to introduce you to
the new future-oriented technology that is integrated in our Class D
amplifiers.
Class D amplifiers are considerably more efficient than standard ana-
logue technologies. The efficiency of analogue amplifiers is around
60 % whilst our digital power amplifiers convert up to 95 % of the input
energy into sound. You could describe the results as "more sound pro-
duced from less".
Furthermore, digital amplifiers heat up so little that they can also be
installed in places that are not very well ventilated, such as beneath the
seats.
The wire remote control that is included allows you to adjust the bass
level conveniently from your seat. To ensure that the sound quality is
optimised, we recommend that the installation of your new Velocity
amplifier be carried out by an authorised Velocity dealer.
Please allow us to make a few comments on the issue of health:
When listening to music in your vehicle, remember that continuous sound
pressure levels of over 100 dB can lead to permanent hearing damage
and even total hearing loss. Modern high-powered systems and high-
quality loudspeaker configurations are capable of producing sound
pressure levels exceeding 130 dB.
We are convinced that you will very quickly appreciate the advantages
of our Class D amplifiers and we would like to take this opportunity to wish
you a lot of fun with this new component in your sound system.
We provide a manufacturer guarantee for our products bought within
the European Union. You can view the guarantee conditions at
www.blaupunkt.de or ask for them directly at:
Blaupunkt GmbH
Hotline
Robert-Bosch-Str. 200
D-31139 Hildesheim
You can also obtain further information on our Velocity series on the
Internet at http://www.velocity.de

Safety notices

nstallation and connection instructions
I
The Burning Desire II is an amplifier that uses high-cur-
rent technology. The short circuit current can exceed
900 amps.
This makes it absolutely necessary for installation to be
carried out by a specialist workshop!
When connecting, make sure that the polarity is correct.
If ever the poles are reversed, the amplifier must be ta-
ken out of service.
After disconnecting the supply voltage, the Burning Des-
ire II must be sent in to the Blaupunkt customer service
centre. Only replace the fuses after reinstallation has
been carried out.
The battery's negative terminal must remain disconnected whilst you
are installing and connecting the unit.
You must observe the vehicle manufacturer's safety notices (airbags,
alarm systems, trip computers, immobilizers) regarding this.
As regards safety in the event of an accident, the Velocity power ampli-
fier must be professionally secured in position. The surface to which it is
attached must be suitable for the screws that are included and must
provide a secure hold.
When drilling holes, you must always make sure that none of the vehic-
le components (e.g. battery, cables, fuse box) are damaged in the pro-
cess.
The amplifier must be secured in a suitable installation location, e.g.
beneath the seats or in the car boot (see Fig. 1).
When choosing an installation location, you should select one which is
dry and which provides sufficient air circulation to cool the amplifier.
Use cable grommets to protect cables against sharp-edged holes.
Use loudspeakers with an impedance of 1-4
load rating (music power rating).
Use loudspeaker connection cables up to 16 mm
loudspeakers to ground - only use the correct terminals as indicated.
The cross section of the positive and negative cables must be at
least 25 mm 2 .
The positive cable between the battery and the amplifier must be
protected directly at the battery using a fuse holder (100 A).
The positive cable must be protected directly at the amplifier using
the fuse holder that is included (4 x 80 A).
Note:
You must make sure that the fuse holder is protected effectively
against moisture.
Load Output
OHM WATT
4 OHM 1000W
1200W
2 OHM
2000W
1500W
1 OHM
2000W
Note:
In the case of longer supply lines to the vehicle battery, a second
battery can be installed alongside the amplifier in order to stabilise
the voltage. This must be installed by a professional workshop.
Velocity Competition Amplifier Burning Desire II
The amplifier is suitable for connection to car audio systems that are
equipped with RCA connections.
If you want to connect it to car audio systems that are equipped with an
ISO connection, please use the Blaupunkt ISO-RCA adapter.
3
Ω
. Observe the maximum
2 . Do not connect
Amplifier Battery
fuses capacity
AMPERE 60AH
100A 60A X 2
140A 60A X 3
240A 60A X 4
240A 60A X 4
320A 60A X 6