Clatronic CL 3542 Instrucciones De Servicio página 34

NOTE
• You may also cancel the timer function at any time by press-
ing the POWER button to turn the unit on/off.
Emptying the water tank (see figure on page 4)
The unit integrates a water tank for collecting condensation.
When this tank is full, the unit will emit several beeps. The unit will
automatically switch into STANDBY mode. The
flashing on the display.
You must empty the water tank in order to continue operation. To
do so, use a floor towel, a flat bowl that can collect approx. 1 liter
of water, as well as the water hose and adapter (22) provided.
1. Disconnect the mains plug from the wall socket.
2. Place the floor towel and the flat bowl underneath the water
outlet.
WARNING:
• Always disconnect the mains plug from the wall socket before cleaning!
• Make sure no water enters the openings of the unit during cleaning.
• Never immerse the appliance in water! Otherwise this might result in an electric shock or fire.
CAUTION:
• Do not spray the device with cleaning agents.
• Do not use a wire brush or any abrasive items.
• Do not use any acidic or abrasive detergents.
Filter
When using the unit daily, clean the filter every 2 weeks. If dust in
the filters blocks the air circulation, efficient operation of the unit
can no longer be guaranteed.
1. First, remove the filters located on the back of the unit side-
ways. Then remove the filters located on the side of the unit.
2. Vacuum the filters for cleaning.
3. Clean the filters under running water. If necessary, use a mild
detergent.
4. Let the filters air-dry in a shady place.
5. Reinstall the filters when completely dry.
CAUTION:
Do not operate the unit without the filter!
Housing
• Use a vacuum cleaner to vacuum the fins and ventilation
openings.
• Wipe the housing with a slightly damp cloth.
Seasonal cleaning and storage
When not using the unit for a long period of time, proceed as fol-
lows:
1. Empty the water tank as described above.
2. Operate the unit in "Fan" mode for 2 hours in order to dry
the inside of the unit.
34
3. Remove the bushing from the outlet.
4. Connect the adapter to the nut and water hose.
5. Remove the rubber plug and keep it for later use.
6. Connect the water hose to the water outlet of the unit.
7. If possible, put the bowl on a lower level than the unit. Place
the end of the water hose in the bowl.
8. Remove the water hose after all the water has been drained.
Close the water outlet of the unit, reattaching the rubber
icon will be
plug and the nut in order to facilitate the condensation
cooling circuit.
Terminating operation
1. Press the POWER
2. Disconnect the mains plug from the wall socket.
Cleaning
3. Press the POWER
the mains plug from the wall socket.
4. Clean the filters and the unit as described above.
5. Disconnect the flexible exhaust pipe from the unit.
6. Cover the unit with foil.
7. Always store the appliance out of the reach of children in a dry,
well ventilated place.
Problem
Unit does not
function
Unit does not
cool sufficiently
button to turn off the unit.
button to turn off the unit. Disconnect
Troubleshooting
Possible cause Solution
No power supply. Check the power con-
nection.
Timer function is activa- Press the POWER
ted. button to turn on the
unit.
The icon is flashing Empty the water tank.
in the display. You may then restart
the unit again.
The unit is exposed to Choose another lo-
direct sunshine. cation or shade the
windows.
Windows or doors are Close any windows or
open. doors.
There are too many Remove portable hea-
people or other heating ters or switch them off.
sources in the room.
The filters are dirty. Clean the filters.
The air inlet or air outlet Remove the blockage.
is blocked. Keep the ventilation
openings free from
obstructions.