Technical Data - Hilti TE 2 Manual De Instrucciones

Technical data

Rated power
Nominal voltage *
Nominal current input *
Mains frequency
Weight of tool without side handle
Weight as per EPTA-Procedure 01/2003
Dimensions (l×h×w)
Minimum distance between wall and hole drilled
Speed
Hammering speed:
Precision hammering action
Full hammering action
Single impact energy Nm (J):
Precision hammering action
Full hammering action
Typical drilling performance in medium-hard B35
concrete
-NOTE-
The vibration emission level given in this information sheet has been measured in accordance with a standardised
test given in EN 60745 and may be used to compare one tool with another. It may be used for a preliminary asses-
sment of exposure. The declared vibration emission level represents the main applications of the tool. However if
the tool is used for different applications, with different accessories or poorly maintained, the vibration emission
may differ. This may significantly increase the exposure level over the total working period. An estimation of the
level of exposure to vibration should also take into account the times when the tool is switched off or when it is
running but not actually doing the job. This may significantly reduce the exposure level over the total working peri-
od. Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the
tool and the accessories, keep the hands warm, organisation of work patterns.
Noise and vibration information (measured in accordance with EN 60745-2-6):
Typical A-weighted sound power level (LwA):
Typical A-weighted emission sound power level (LpA):
For the given sound power level
as per EN 60745, the tolerance is
Wear ear protection!
Triaxial vibration value (vibration vector sum)
measured in accordance with EN 60745-2-1
Drilling in metal, (a )
h, D
measured in accordance with EN 60745-2-6
Hammer drilling in concrete, (a
Uncertainty (K) for triaxial vibration value
* The tool is offered in different versions for various mains voltages. Please refer to the information on the
type plate for the nominal voltage and nominal current input of your tool.
)
h, HD
650 W
100 V 110 V 120 V
6.9 A 6.5 A 6.5 A
50–60 Hz
2.4 kg (TE2 / TE2-S / TE2-E)
2.7 kg (TE2-M)
2.7 kg (TE2 / TE2-S / TE2-E)
2.9 kg (TE2-M)
352×203×89 mm (TE 2 / TE 2-E / TE 2-S)
360×203×89 mm (TE 2-M)
34 mm
0– 930 r.p.m. (hammer drilling)
0–1200 r.p.m. (in 1st gear TE2 / TE2-E / TE2-S / TE2-M)
0–2500 r.p.m. (in 2nd gear TE 2-M)
0–2600 blows/min. (TE 2-S)
0–4600 blows/min. (TE 2 / TE 2-E / TE 2-S / TE 2-M)
0.6 Nm (TE 2-S)
1.8 Nm (TE 2 / TE 2-E / TE 2-S / TE 2-M)
8 mm dia.: 550 mm/min
10 mm dia.: 500 mm/min
12 mm dia.: 400 mm/min
102 dB (A)
91dB (A)
3 dB
2.8 m/s 2
13.5 m/s 2
1.5 m/ s 2
220 V 230 V 240 V
3.1 A 3.0 A 2.9 A
en
13