Proper Use; Technical Data - EINHELL TC-TS 200 Manual De Instrucciones

3. Proper use

The bench-type circular saw is designed for the
slitting and cross-cutting (only with the cross
stop) of all types of timber commensurate with the
machine‘s size. The equipment is not to be used
for cutting any type of round wood.
The equipment is to be used only for its prescri-
bed purpose. Any other use is deemed to be a
case of misuse. The user / operator and not the
manufacturer will be liable for any damage or inju-
ries of any kind caused as a result of this.
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.
The equipment is to be operated only with suita-
ble saw blades (saw blades made of HM or CV)
It is prohibited to use any type of HSS saw blade
and cutting-o wheel.
To use the equipment properly you must also
observe the safety information, the assembly
instructions and the operating instructions to be
found in this manual.
All persons who use and service the equipment
have to be acquainted with these operating
instructions and must be informed about the
equipment‘s potential hazards. It is also imperati-
ve to observe the accident prevention regulations
in force in your area. The same applies for the
general rules of health and safety at work.
The manufacturer will not be liable for any chan-
ges made to the equipment nor for any damage
resulting from such changes. Even when the
equipment is used as prescribed it is still impossi-
ble to eliminate certain residual risk factors.
The following hazards may arise in connection
with the machine‘s construction and design:
•
Contact with the saw blade in the uncovered
saw zone.
•
Reaching into the running saw blade (cut
injuries).
•
Kick-back of workpieces and parts of work-
pieces.
•
Saw blade fracturing.
•
Catapulting of faulty carbide tips from the saw
blade.
•
Damage to hearing if essential ear-muffs are
not used.
GB
•
Harmful emissions of wood dust when used
in closed rooms.

4. Technical data

Mains voltage: ..........................230-240V ~ 50Hz
Power: .........................500 W S1, 800 W S6 15%
Idle speed n : ....................................... 2950 rpm
0
Carbide saw blade: ......... Ø 200 x Ø 16 x 2.4 mm
Maximum tooth pitch ............................... 2.4 mm
Number of teeth: ............................................ 24
Table size: ..................................... 505 x 373 mm
Max. cutting height: ......................... 45 mm / 90°
........................................................ 27 mm / 45°
Dust extraction connector: ....................Ø 36 mm
Weight: ....................................... approx. 11.6 kg
Thickness of the splitter: ......................... 2.2 mm
Operating mode S6 15%: Continuous operation
with idling (cycle time 10 minutes). To ensure that
the motor does not become excessively hot, it
may only be operated for 15% of the cycle at the
speci ed rating and must then be allowed to idle
for 85% of the cycle.
Danger!
Noise
The noise emission values were measured in ac-
cordance with EN 62841.
Operation
L sound pressure level ..................... 87.2 dB(A)
pA
K uncertainty ........................................ 3 dB(A)
pA
L sound power level ..................... 100.2 dB(A)
WA
K uncertainty ........................................ 3 dB(A)
WA
Wear ear-mu s.
The impact of noise can cause damage to hea-
ring.
The stated noise emission values were measured
in accordance with a set of standardized criteria
and can be used to compare one power tool with
another.
The stated noise emission values can also be
used to make an initial assessment of exposure.
Warning:
The noise emission levels may vary from the level
speci ed during actual use, depending on the
- 21 -