Multiplex EasyGlider Instrucciones De Montaje página 11

EasyGlider KIT
EasyGlider Electric KIT
Examine your kit carefully!
MULTIPLEX model kits are subject to constant quality checks throughout the production process, and we sincerely hope that you
are completely satisfied with the contents of your kit. However, we would ask you to check all the parts before you start
construction, as we cannot exchange components which you have already worked on. If you find any part is not acceptable for
any reason, we will readily correct or exchange it. Just send the component to our Model Department. Please be sure to include
the purchase receipt and a brief description of the fault.
We are constantly working on improving our models, and for this reason we must reserve the right to change the kit contents in
terms of shape or dimensions of parts, technology, materials and fittings, without prior notification. Please understand that we
cannot entertain claims against us if the kit contents do not agree in every respect with the instructions and the illustrations.
Caution!
Radio-controlled models, and especially model aircraft, are by no means playthings. Building and operating them safely
requires a certain level of technical competence and manual skill, together with discipline and a responsible attitude at the
flying field. Errors and carelessness in building and flying the model can result in serious personal injury and damage to
property. Since we, as manufacturers, have no control over the construction, maintenance and operation of our products,
we are obliged to take this opportunity to point out these hazards and to emphasise your personal responsibility.
Additional items required for the EasyGlider / EasyGlider Electric:
Adhesives: cyano-acrylate ("cyano") and activator
Use medium-viscosity cyano glue (not styrofoam cyano) in conjunction with activator ("cyano kicker"). Epoxy adhesives produce
what initially appears to be a sound joint, but the bond is only superficial, and the hard resin breaks away from the parts under
load.
Hot-melt glue (from a glue gun) can be used as an alternative.
MULTIPLEX radio control system components for the EasyGlider and EasyGlider Electric:
PiCO 5/6 UNI receiver
alternatively
or
Micro IPD UNI receiver
alternatively
Tiny-S UNI servo (2 required)
Nano-S UNI servo (2 required)
600 mm UNI extension lead
if necessary: 200 mm UNI separation filter cable
Battery charger:
MULTIcharger 5008 DC (charge current 100 mA ... 5A)
for use with 12 V power supply, e.g. car battery
Additional items for EasyGlider Electric only
MULTIcont X-16 UNI
MULTIPLEX Permabatt NiMH flight battery
or MULTIPLEX Permabatt NiMH flight battery
Plug / socket for speed controller / flight battery
Additional items for EasyGlider only
NiMH receiver battery
Mini switch harness with charge socket
Rubber bungee launch system for EasyGlider
Tools:
Scissors, balsa knife, side-cutters, soldering iron.
Note: remove the picture pages from the centre of the building instructions.
Specification
Wingspan
Overall length
Fuselage length
All-up weight
Wing area
Wing loading
RC functions
# 21 4205
# 21 4207
EasyGlider
1800 mm
1130 mm
1060 mm
approx. 710 g
FAI approx. 41.6 dm²
approx. 17 g / dm²
Elevator, rudder, ailerons
GB
35 MHz, e.g. A-band
40 MHz
35 MHz, e.g. A-band
40 MHz
Elevator / rudder
2 x ailerons
Aileron servos, 2 x
Aileron servos, 2 x
1 - 8 cells NiCd / NiMH
Speed controller
7 / 1500 mAh
8 / 1500 mAh
6-pin green
4 / 1500 mAh
15 m special rubber cord
100 m towline on reel
EasyGlider Electric
1800 mm
1115 mm
1020 mm
with standard power system approx. 880 g
FAI approx. 41.6 dm²
approx. 21 g / dm²
Plus throttle
Order No. 5 5920
Order No. 5 5921
Order No. 5 5971
Order No. 5 5972
Order No. 6 5121
Order No. 6 5120
Order No. 8 5032
Order No. 8 5035
Order No. 9 2525
Order No. 7 2271
Order No. 15 6030
Order No. 15 6037
Order No. 8 5213
Order No. 15 6029
Order No. 8 5037
Order No. 72 3388
11