JB Systems Light Strobe IGNITOR BF-04D Manual De Instrucciones página 4

ENGLISH
FUNCTIONS
(FRONT)
IMPORTANT: You can connect analog AND DMX strobes to this device. When you connect analog strobes,
the dimmer slider (n°7) will have no effect. When you connect 2 channel DMX strobes, the dimmer slider
(n°7) will have effect when the selected DMX strobe has a dimmer function.
 Channel 1: speed rate
 Channel 2: dimmer 20  100 %
If you use 2 channel DMX strobes, you have to set the DMX addresses of the strobes first
For DMX strobes where the addresses have to be set by DIP-switches,
check
the table and the examples below:
Examples:

Channel 1 : dip / on : #1 ( 1 )

Channel 3 : dip / on : #1, #2 ( 1 + 2 = 3)

Channel 5 : dip / on : #1, #3 ( 1 + 4 = 5 )

Channel 7 : dip / on : #1, #2, #3 ( 1 + 2 + 4 = 7 )
1. BLACKOUT BUTTON: This button is used to blackout the attached strobes.
2. FULL ON BUTTON: All strobes will light at high speed rate and full output power.
3. SINGLE FLASH BUTTON: When the unit is set in blackout, you can tap this button to flash all strobes 1
time.
4. CHASE BUTTONS: Press the up/down button to choose one of the 10 built-in patterns.
Pattern 0 Random pattern
Pattern 1 1234 Full on
1-2-3-4 ― 4-3-2-1
Pattern 2
Pattern 3 1-2-3-4-3-2-1
12-34 ― 24-13 ― 23-14
Pattern 4
1-12-123-1234-123-12-1-stop ―4-43-432-4321-432-43-4-stop
Pattern 5
Pattern 6 1-12-123-1234-234-34-4-stop―4-43-432-4321-321-21-1-stop
Pattern 7 1-3-2-4-3-1-4-2
12-23-34-41 ― 43-32-21-14
Pattern 8
Pattern 9 1 2-1 2 3-1 2-1 2 3 4
5. MODE BUTTON: While pressing this button, you can choose between 2 working modes:
JB SYSTEMS
®
OPERATION MANUAL
3/26 BF-04D STROBE IGNITOR
ENGLISH

Green LED is lit: You are working in SOUND MODE. The strobes will react to the music.
(internal micro)

Yellow LED is lit: You are working in AUTO MODE. You can choose one of the chases by using
the chase button (see n° 4).
6. SPEED SLIDER: With this slider, you can choose the flash rate of the strobes.
7. DIMMER SLIDER: Does not work on analog strobes. Works on DMX strobes when they have a dimmer
function. You can set the output power from 20% to 100%
FUNCTIONS
(REAR)
1. POWER SWITCH: Used to switch the unit ON/OFF.
2. DC POWER INPUT: Used to connect the supplied 9V/500mA DC adapter to the controller.
3. 4 JACK CONNECTIONS: Used to connect analog strobes with 1/4" MONO JACK.
4. DMX OUTPUT: Used to connect DMX strobes.
CONNECTIONS
You can connect both analog and/or DMX strobes at the same time. The n° of strobes in the chain of the
analog strobes is set to a maximum of 5 units.
SPECIFICATIONS
Power Input: DC 9V 500mA minimum.
AC 230V, 50Hz  9Vdc / 500mA (or more)
AC/DC Power adapter:
DMX outputs: 3pin XLR
Analog outputs: 12Vdc pulses
Audio input: None, internal microphone
Size: 210 x 133 x 77 mm
Weight: 0,8 kg
Every information is subject to change without prior notice
You can download the latest version of this user manual on our website: www.beglec.com
JB SYSTEMS
®
OPERATION MANUAL
4/26 BF-04D STROBE IGNITOR