Publicidad
Idiomas disponibles
Idiomas disponibles
FIG. 1
MODE DE RÉGLAGE DU TRÉPAN ORDINAIRE
MODO DE AJUSTE DE LA BROCA DE CINCEL
HAMMERDRILLING MODE
MODE DE MARTEAU PERFORATEUR
MODO TALADRO PERCUTOR
MODE DE RÉGLAGE DU TRÉPAN ORDINAIRE
MODO DE AJUSTE DE LA BROCA DE CINCEL
J
H
C
FIG. 2
M
K
N
O
P
L
J
H
C
FIG. 4
Q
R
U
G
S
T
COMPONENTS (Fig. 1)
WARNING: Never modify the power tool or any part of it. Damage or personal injury could
result.
A. Trigger switch
F. Mode selector
B. Lock-on slider
G. Electronic Speed and impact control dial
C. Side handle
H. Clamp knob
D. Main handle
I. Rear side handle position
E. Active vibration control
INTENDED USE
These heavy-duty rotary hammers have been designed for professional hammerdrilling and
chipping at various work sites (i.e., construction sites). DO NOT use under wet conditions or in
presence of flammable liquids or gases.
These heavy-duty rotary hammers are professional power tools. DO NOT let children come into
contact with the tool. Supervision is required when inexperienced operators use this tool.
ASSEMBLY AND ADJUSTMENTS
Side Handle (Fig. 1)
WARNING: To reduce the risk of personal injury, ALWAYS operate the tool with the side
handle properly installed and securely tightened. Failure to do so may result in the side handle
slipping during tool operation and subsequent loss of control. Hold tool with both hands to
maximize control.
The side handle clamps to the front barrel (collar) and may be rotated 360° to permit right
or left-hand use. For operating convenience, the side handle can be installed in front or rear
positions.
TO MOUNT IN FRONT POSITION (FIG. 3)
1. Unscrew the side handle (C) and disassemble the side handle clamp (J).
2. Snap the steel ring (K) over the collar (L) behind the tool holder (M). Squeeze both ends of
the steel ring together. Mount the bushing (N) and insert the pin (O).
3. Slide the side handle clamp (J) and bushing into the clamp knob (H) – do not tighten.
4. Screw the side handle (C) into the clamp knob (H) and tighten.
5. Rotate the side handle mounting assembly to the desired position. For hammerdrilling
horizontally with a heavy drill bit, place the side handle assembly at an angle of approximately
20° to the tool for optimum control.
6. Lock the side handle mounting assembly in place by tightening the clamp knob (H).
TO MOUNT IN REAR POSITION (FIG. 3)
1. Unscrew the side handle (C) and remove it from the side handle mounting assembly. Leave
the side handle mounting assembly in the front position.
2. Screw the side handle directly into one of the rear side handle positions (I) on either side of
the tool.
Active Vibration Control (Fig. 1)
For best vibration control, hold the tool with one hand on the main handle (D) and the other
hand on the side handle (C). Apply just enough pressure so the hammer is approximately mid-
stroke. The hammer only needs enough pressure to engage the active vibration control. Applying
too much pressure will not make the tool drill or chip faster and active vibration control will not
engage.
CHISEL BIT ADJUSTMENT MODE
CHIPPING MODE
MODE DE BURINAGE
MODO CINCEL
CHISEL BIT ADJUSTMENT MODE
E
I
F
FIG. 3
I
Inserting and Removing SDS Max
WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect tool
from power source before making any adjustments or removing/installing attachments or
accessories.
1. Pull back the locking sleeve (P) and insert the bit shank. The bit shank must be clean and
slightly lubricated.
2. Turn the bit slightly until the sleeve snaps back into position.
3. Ensure the bit is properly engaged.
NOTE: The bit needs to move several centimeters in and out of the tool holder (M) when
properly engaged.
4. To remove the bit, pull back the locking sleeve and pull the bit out.
Complete Torque Control (Fig. 4)
NOTICE: Always turn the tool off before changing torque control settings or damage to tool may
result.
The Complete Torque Control (CTC) feature of this tool is designed to provide additional control
with a two-stage clutch mechanism.
Clutch Setting 1 (Q) is designed for most hammerdrilling applications and is designed to easily
clutch out when the drill bit encounters re-bar or other foreign substances.
Clutch Setting 2 (R) is designed for higher torque applications such as core-bits and deep hole
D
hammerdrilling and is designed to clutch out at a higher torque threshold.
Move the torque control lever (U) to setting 1 or 2 as needed for application.
A
NOTE: Allow the motor housing to rotate a little while changing torque.
Each time the tool is plugged in, it will automatically default to clutch setting 1, the most
sensitive setting.
B
Electronic Speed and Impact Control (Fig. 4)
The electronic speed and impact control allows the use of smaller drill bits without the risk of bit
G
breakage, hammerdrilling into light and brittle materials without shattering and optimal tool control for
precise chiseling.
To set the control dial, turn the dial (G) to the desired level. The higher the number, the greater
E
the speed and impact energy. Dial settings make the tool extremely flexible and adaptable
for many different appli cations. The required setting depends on the bit size and hardness of
material being drilled.
Mode Selector (Fig. 1)
CAUTION: Never change the mode while the unit is running.
CAUTION: Do not change to hammerdrill mode with chisel bit in tool holder. Personal injury
and damage to tool may result.
The D25712 an D25762 use two operating modes. To select the required operating mode, rotate
the mode selector (F) until the arrow points to the hammerdrilling or the chipping icon. The
D25831 and D25851 use only the chipping mode.
HAMMERDRILLING MODE (
The tool simultaneously rotates and impacts the work. This mode is appropriate for all concrete
and masonry operations.
CHIPPING MODE (
The spindle lock is engaged during chipping mode so the tool impacts the work without
rotating. This mode is appropriate for light chipping, chiseling and demolition applications.
NOTE: In chipping mode, the hammerdrill can also be used as a lever to free a jammed drill bit.
CHISEL BIT ADJUSTMENT (
Turn the mode selector to one of the chisel bit adjustment icons to adjust the chisel to the desired
position. There are 24 possible positions to set the angle of the chisel. After finding the desired
position, slightly maneuver the chisel bit back and forth to ensure the chisel is properly engaged.
Power Indicator Lights (Fig. 4)
The yellow brushwear indicator LED (S) lights up when the carbon brushes are nearly worn out
indicating that the tool needs servicing within the next 8 hours of use.
The red indicator LED (T) lights up if the lock-on button (B) is used in any mode except the
C
chipping mode.
The red indicator LED (T) starts to flash if there is a fault with the tool or the brushes have
completely worn out (refer to Brushes under MAINTENANCE).
OPERATION
WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect tool
from power source before making any adjustments or removing/installing attachments or
accessories.
WARNING: To reduce the risk of personal injury, ALWAYS ensure workpiece is anchored
or clamped firmly. If hammerdrilling thin material, use a wood "back-up" block to prevent
damage to the material.
WARNING: To reduce the risk of personal injury, ALWAYS operate the tool with the side
handle properly installed and securely tightened. Failure to do so may result in the side
handle slipping during tool operation and subsequent loss of control. Hold tool with both hands
to maximize control.
Proper Hand Position (Fig. 1)
WARNING: To reduce the risk of serious personal injury, ALWAYS use proper hand position
as shown.
WARNING: To reduce the risk of serious personal injury, ALWAYS hold securely in anticipation
of a sudden reaction.
Proper hand position requires one hand on the side handle (C), with the other hand on the main
handle (D).
NOTE: Operating temperature of this tool is 19˚ to 104˚ F (-7 to +40˚ C). Using the tool outside
of this temperature range will decrease the life of the tool.
Trigger Switch (Fig. 1)
To turn the tool on, depress the trigger switch (A). To stop the tool, release the trigger switch. To
lock the trigger switch on in the chipping mode only, push the lock-on slider (B) upwards while
depressing the trigger switch.
To deactivate the lock-on slider, depress the trigger switch once then release.
The lock-on slider may only be activated in chisel mode. The machine will stop running when
trying to engage the lock-on slider in drill mode. The motor will stop if the lock-on slider is
activated when changing from chisel mode into drill mode.
SOFT START FEATURE
The soft start feature allows you to build up speed slowly, thus preventing the drill bit from
walking off the intended hole position when starting. The soft start feature also reduces the
immediate torque reaction transmitted to the gearing and the operator if the hammer is started
with the drill bit in an existing hole.
Hammerdrilling with a Solid Bit
D25712, D25762
NOTE: The D25891 have only chipping modes with no hammerdrilling capability.
1. Set the mode selector to hammerdrilling mode.
2. Move the torque control lever to Setting 1 (Q).
3. Set the speed and impact control dial.
4. Insert the appropriate drill bit.
5. Adjust the side handle (front or rear position).
6. Mark the spot where the hole is to be drilled.
7. Place the drill bit on that mark and depress the trigger switch.
8. Apply only enough pressure to engage active vibration control (refer to Active Vibration
Control).
9. To stop the tool, release the trigger switch. Always turn the tool off when work is finished and
before unplugging.
Hammerdrilling with a Core Bit
D25712, D25762
CAUTION: Do not use a core bit for hammerdrilling wood. Personal injury and damage to tool
may result.
NOTE: The D25891 has only chipping mode with no hammerdrilling capability.
1. Set the mode selector to hammerdrilling mode.
2. Move the torque control lever to Setting 2 (R).
3. Turn the speed and impact control dial to the maximum torque position.
4. Adjust the side handle (front or rear position).
5. Assemble the centering bit and adapter shank into core bit.
6. Mark the spot where the hole is to be drilled.
7. Place the centering bit on that mark and depress the trigger switch.
NOTE: Some core drills require the removal of centering bit after about 1 cm of penetration. If
so, remove and continue hammerdrilling.
8. When hammerdrilling through a structure thicker than the depth of the core bit, break away
the round cylinder of concrete or core inside the bit at regular intervals. To avoid unwanted
breaking away of concrete around the hole, first drill a hole the diameter of the centering
bit completely through the structure. Then drill the cored hole halfway from each side of
the structure.
9. To stop the tool, release the trigger switch. Always turn the tool off when work is finished and
before unplugging.
Chipping and Chiseling
1. Set the mode selector to chipping mode.
2. Set the impact control dial to desired setting (refer to Electronic Speed and Impact
Control).
®
Accessories (Fig. 3)
)
)
)
Publicidad
