Publicidad
Idiomas disponibles
Idiomas disponibles
16 Foot
17 Bevel clamp handle
A3
17 Bevel clamp handle
18 Height adjuster
19 Saw bench table
20 Riving knife
21 Upper blade guard
22 Parallel fence
23 Push stick
Optional accessories
For use in mitre saw mode:
30 Fence insert (DE7120)
A5
31 Adjustable stand 760 mm (max. height) (DE3474)
32 Support guide rails 1,000 mm (DE3494)
33 Support guide rails 500 mm (DE3491)
34 Inclinable support (DE3495)
35 Swivelling stop (DE3462)
36 Length stop for short workpieces (to be used with guide rails [33])
(DE3460)
37 Support with removable stop (DE3495)
38 Support with stop removed (DE3495)
39 Material clamp (D271051)
A6
40 Roller support table (DE3497)
For use in saw bench mode:
A7
41 Mitre fence (D271052)
A8
42 Extension table (D271058)
A9
43 Sliding table (D271055)
Push sticks (DE3454) (not shown)
For use in all modes:
A10
44 Three way dust extraction kit (D271054)
Electrical safety
The electric motor has been designed for one voltage only. Always check
that the power supply corresponds to the voltage on the rating plate.
Using an extension cable
If an extension cable is required, use an approved extension cable suitable
for the power input of this machine (see technical data). The minimum
conductor size is 1.5 mm2.
When using a cable reel, always unwind the cable completely.
Also refer to the table below.
Conductor size (mm2)
Cable rating (Amperes)
1.50
15
2.50
20
4.00
25
Cable length (m)
7.515 25
30
45
60
Voltage
Amperes
Cable rating (Amperes)
230
0 - 2.0
6
6
2.1 - 3.4
6
6
3.5 - 5.0
6
6
5.1 - 7.0
10
10
7.1 - 12.0
15
15
12.1 - 20.0
20
20
Assembly and adjustment
Prior to assembly and adjustment always unplug the tool.
Unpacking the machine and its parts
When moving the machine, always seek assistance.
The machine is too heavy for one person to handle.
• Remove the loose packaging material from the box.
• Lift the machine out of the box.
• Remove the parts box from the interior of the machine.
• Remove any remaining packing material from the machine.
Mounting the feet (fig. B)
With the feet mounted, the machine is suitable for placement on a
workbench. To ensure a safe operation, the machine has to be fixed to the
workbench.
• Turn the machine upside down.
• Place a foot (16) on each of the mounting locations (51) on the base.
• Slide a nut (52) into the slots (53) located above the mounting
locations.
• Insert a bolt (54) fitted with a washer (55) into the feet.
• Tighten the bolts.
• Mount the legs as described below.
• Fold the legs as described below.
• Turn the machine straight up.
• Fix the machine to the workbench.
Mounting the legs (fig. C1 & C2)
With the legs mounted, the machine is suitable for stand-alone placement.
• Turn the machine upside down.
• Mount the legs as described below. Beware that the front legs and the
rear legs have different lengths. The rear legs are slightly longer than
the front legs. Make sure to mount the legs in the correct place.
• Turn the machine straight up. Make sure it is level; adjust the leg
clamping height if required.
Rear legs
• Present a leg (15) to each of the mounting points (56) located at the
lower edges on the inside of the base (fig. C1).
• Pass a coach bolt (57) from the outside through the holes into the
frame and the legs.
• Place a bracket (58) and a lock knob (59) onto the bolts.
• Tighten the lock knobs.
Front legs
• Present a leg (15) to each of the mounting points (56) located at the
upper edges on the inside of the base (fig. C2).
• Place a bracket (58) over the legs.
• Pass a coach bolt (57) from the inside through the holes into the
brackets, the legs and frame.
• Place a lock knob (59) onto the bolts.
• Tighten the lock knobs.
E N G L I S H
6
6
6
6
6
6
6
6
6
6
10
15
10
10
15
15
15
15
20
20
20
20
25
-
39
Publicidad
