Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
lected. When the CEPT frequency band is selected, "UK" disappears from
the display (see table on page 45).
ANL
(long press)
Automatic Noise Limiter. This filter allow reducing back ground noises and
some reception interferences.
Long press the ANL key (8) to
activate/disable
on the display when the filter is activated.
Note: ANL filter works only in AM mode
9) USB CHARGING SOCKET
The USB socket (9) can be used to charge smartphones, tablets or other
rechargeable devices with 5 V - 2.1 A.
10) 6 PIN MICROPHONE PLUG
The plug is located on the front panel of the transceiver and makes the
setting of the equipment into the dashboard easier.
See Cabling Diagram page 48.
11) PTT (Push To Talk)
Transmission key, press to
transmit
to
listen to
an incoming communication,
TOT (Time Out Timer)
If the transmission using PTT switch (11) or VOX function is longer than 3
minutes, the display starts blinking and the transmission ends. A beep will
sound until the PTT switch (13) key is released.
12) UP/DN BUTTONS ON MICROPHONE ~ SCAN
UP/DN BUTTONS ON MICROPHONE
Press UP/DN buttons (12) on the microphone to
increase
and DN to
decrease
See ROTARY KNOB page 28.
SCAN
(very long press)
Press and hold the UP or DN button (12) for ± 7 seconds or until a beep
activate
the SCAN function. The dot between the two channel
sounds to
digits flashes to indicate that the function is active.
the ANL filter. "ANL" appears
a message,
is displayed and release
disappears.
(short press)
change
the channel. UP to
the channel.
The scanning stops as soon as there is a busy channel. The scanning au-
tomatically starts 3 seconds after the end of the transmission and no key
is activated during 3 s. In
SCANNING
press the UP/DN buttons (12) on the microphone to change scan direction.
Press PTT switch (11) to exit SCAN. The dot between the two channel digits
disappears from LCD.
A) DC-POWER TERMINAL (13.2 V / 26.4 V)
B) ANTENNA CONNECTOR (SO-239)
C) JACK FOR EXTERNAL OPTIONAL SPEAKER (8 Ω, Ø 3.5 mm)
D) JACK FOR OPTIONAL VOX MICROPHONE (8 Ω,Ø 2.5 mm)
C) FUNCTIONS TURNING ON THE UNIT
1) COLOR
choose
This function allows to
1.
Turn on the power while pressing the MODE key (8). The letter corresponding
to the current color blinks.
2.
Turn the ROTARY knob (4) or use UP/DN buttons (12) on the microphone to
select
the color. 7 available colors over and over :
3.
Press PTT switch (11) to
validate
an long beep sounds to
confirm
BEEP page 30).
4.
If no key is pressed for 5 seconds, the unit automatically
SETTING without save.
Default COLOR is:
(orange).
2) KEY BEEP
When the function is activated, a beep
changing the channel etc. "BP" appears on the display when the function
is active.
1.
Turn on the power while pressing the DN button (12) on the microphone.
The display shows "BP" and the current status, OF or On, of the function.
2.
Repeat the point 1 until the display shows the desired status.
3.
Release the DN key on the microphone.
Default KEY BEEP is On.
30
mode, turn the ROTARY knob (4) or
the backlight color of the LCD.
and exit. If the KEY BEEP function is activated,
the succes of the operation (see § KEY
exits
the COLOR
sounds
when a key is pressed, by
Publicidad
Tabla de contenido
