CAB SUPERBE SR1.60 Manual De Instrucciones página 10

The motor can be mounted in two different ways:
Mounting on existing shutter (Picture 1a)
In case of existing shutters, install the motor by drilling vertically the pole (A).
1) Fix the gearmotor on the pole (2) by means of the bracket (1) and the 4 fixing screws (V).
2) Lock the gearmotor on the pole by means of the screws 3/5/7 and related nuts 4/6/8.It is also possible using
a single passing screw instead of screws 3/5 (not supllied).
3) Fix the two crown gears (9) to the gearmotor by means of the screws (10).
4) Make appropriate holes on the pole for the insertion of the electric brake unlock wire (12) and electric cable
sheath (11) making sure that the position of the holes facilitates the insertion of the wire and cables.
5) Fix the shutter by means of the screw (13) and washer (14).In case of crown gears by 220mm each use the
expansion adaptor and screw (15).
Quick fixing on the bar (Picture 1b)
In case of new installation, it is possible insert the gearmotor on the pole without disassemble the crown
gears.
1) Drill through the pole making a hole by 10.5mm.
2) Insert the pole into the gearmotor as it is (without disassemble the crown gears)
3) Fix the gearmotor on the pole by means of three screws and nuts.
1) Remove the cover of the limit switch
2) With rolling gate closed, move switch 2 to OFF (limit switches excluded).
3) After completion of the wire connections, completely open and close the rolling gate.
4) Move switch 2 to ON (limit switches activated).
5) Carry out some movements to check the correct triggering of the limit switches.
6) The system can be manually adjusted by acting on the special toothed ring nut.
7) After adjustment, place the cover on again and fit it by means of a screw.
1) Mount the clutch disk on the upper cover of the electric motor.
2) Use the screws 1 supplied to fix the electrobrake (plate, wound bobbin and sheet metal support) on the
upper cover.
3) Remove the cover of the limit switch 2 box.
4) Connect the two wires of the electric brake to terminals "EF" of the card inside the limit switch box.
5) Place the limit switch box cover on and fit it by means of the special screw.
1) This instruction booklet is only addressed to qualified specialists.
2) Use low voltage to perform up and down movements of the shutter.
3) We recommend the use of original CAB accessories.
4) Use cables with a minimum section of 1.5 mm
5) Cables must not get in contact with metal parts in order to avoid short circuits.
6) All products manufactured by AUTOMATISMI CAB S.r.l. are guaranteed.
The warranty is limited exclusively to repair or substitution cost free of the pieces which will be acknowledged
by the company as faulty due to poor quality of materials or manufacture.
Any complaints will not, under any circumstances, give the Buyer the right to cancel or reduce the order,
nor will it oblige AUTOMATISMI CAB S.r.l. to pay compensation for damages of any kind.
The guarantee loses its validity if the goods, returned as faulty, have been tampered with, repaired or defects
arising from the influence of external agents, incorrect maintenance, overloading, normal wear and tear,
erroneous choice of model, incorrect installation or any other factor not attributable to AUTOMATISMI CAB
S.r.l.
AUTOMATISMI CAB S.r.l. is only responsible for damages caused by any accidents resulting from faulty
products, required by Italian law.
The warranty requires that the system is in compliance with the regulations in force and the accessories
used are original AUTOMATISMI CAB S.r.l. In the event of defective accessories, indicate the serial number
of the motor.
10
Gearmotor installation (fig.1a-b)
Limit switch adjustment (fig.2)
Electrobrake assembly (fig.3)
Notes and guarantee
.
2