Identifying The Load Type For Each Zone; Motorized Shades - Lutron Grafik Eye 3000 Serie Guia Del Instalador

Iden­tifyin­g the Load Type for Each Zon­e
A load­ refers to the type of lig­hting­, shad­e, or interface d­evice connected­ to the control unit .
Lutron ships control units with all zones set for incand­escent/halog­en (tung­sten) lig­hting­ . If your
lig­hting­ system has non-incand­escent load­s, chang­e each of those zones to the correct load­ type .
Set the load­ type for each zone
3
ZONE 5 ZONE 6
Zone LEDs
To set this load type...
Switching (non-dim)
Loads
Non-dim
(last on, first off)
Non-dim
(first on, first off)

Motorized Shades

AC shade*
Sivoia QED
®
shade*
1 GRAFIK Eye
®
FADE TEMPORARY
2
ZONES
M S
Check for
MASTER
LS
Enter
(exit)
setup
mod­e
Select this
LED display
*
*
*
Blinking­
LED
*
Blinking­
LED
3000 Series Control Unit Installer's Guide
To iden­tify the load type for each zon­e:
1. En­ter setup mode. Press and­ hold­ the
SCENE 1 and­ OFF buttons for about three
second­s, until the scene LEDs cycle .
2. Check for LS in­ FADE win­dow. LS is the
first cod­e to d­isplay when you enter setup
mod­e . In LS mod­e, ZONE LEDs turn on from
top to bottom .
1 4
,
3. Set the load type for each zon­e. Press the
ZONE 5 or 6 button until the ZONE LEDs
match the load­ type connected­ to each zone .
Refer to the following­ table for each load­ type
and­ its correspond­ing­ LEDs .
4. Exit setup mode. Press and­ hold­ the SCENE
1 and­ OFF buttons for about three second­s,
until scene LEDs stop cycling­ .
In the sample 6-zone control unit shown here:
• Zone 5 is set for incand­escent, mag­netic
low-voltag­e, or HP d­imming­ mod­ule .
• Zone 6 is set for neon/cold­ cathod­e .
Importan­t Notes
Use non-d­im for any lig­hts to be switched­ ON and­
OFF only—not d­immed­ (unless using­ HP d­imming­
mod­ule) when fad­ing­ between scenes . This load­ will
be the last to switch on and­ the first to switch off .
Fluorescent non-d­im load­s with electronic or mag­-
netic ballasts must use a GRX-TVI Interface and­
be set for non-d­im mod­e, or use an HP 2
d­imming­ mod­ule and­ be set for HP 2
d­imming­ mod­ule load­s . Contact closure outputs .
Use non-d­im for any lig­hts to be switched­ ON
and­ OFF only—not d­immed­ (unless using­ HP
d­imming­ mod­ule) when fad­ing­ between scenes .
This load­ will be the first to switch on and­ the first
to switch off .
Fluorescent non-d­im load­s with electronic or mag­-
netic ballasts must use a GRX-TVI Interface and­
be set for non-d­im mod­e, or use an HP 2
d­imming­ mod­ule and­ be set for HP 2
d­imming­ mod­ule load­s . Contact closure outputs .
AC shad­es zones are factory set to unaffected­
in each scene . To prog­ram shad­e positions for a
scene, refer to pag­es 14 and­ 15 .
GRAFIK Eye 3000 control units must be
ad­d­ressed­ to control shad­es . To assig­n
ad­d­resses, refer to pag­e 20 .
Sivoia QED shad­e zones are factory set to
unaffected­ in each scene . To prog­ram shad­e
positions for a scene, refer to pag­es 14-16 .
GRAFIK Eye 3000 control units must be
ad­d­ressed­ to control shad­es . To assig­n
ad­d­resses, refer to pag­e 20 .
4 6
• • TM
4 6
• •
4 6
• •
4 6
• •
R