Publicidad
Idiomas disponibles
Idiomas disponibles
ii'_l'/lln_j |_m
If your AV component
is not a DENON product or Jf it cannot be operated
Using the preset memory,
Jt can be
controlled
with the included remote
cont@ unit by storing its remote control signals in the remote
cont@
unit
For some remote
cont@
signals it is not possible to "learn"
the signals or the device will not operate propedy
In such cases use the remote cont@
unit included with the device to operate it
2
Press the USE/LEARN button with the tip of a
pen etc, to set the learn mode
• Both
the
mode
selector
buttons
and
LEARNED/TX
indicator flash
Flashes
Press the mode button
of the eq@pment
for
which learning is desired
• Mode
button
and
LEARNED/TX
indicator
flash
2
1,3,7
O O
O O
3
4
5
Press the button that is to be learned
The LEARNED/TX
indicator
stops flashing
and
the mode button lights
• Mode
button
and
LEARNED/TX
indicator
flashed if a button that cannot be "learned"
is
"7
/
pressed
• To cancel, press the USE/LEARN button
Point the remote
control units directly at each
other and press and hold I
Jn the button on the
i, f
other
remote control
v
Other remote
unit which you want
_
control unit
to
learn __
The
mode
button
and
the
LEARNED/TX
indicator
lights, release the button
on the other remote
control unit
• The mode button
and the
LEARNED/TX
indicator start
flashing
again
To "learn"
other buttons, repeat steps 2 to 5
Once the learning operation is completed,
press
the USE/LEARN button
again
The
mode
button
and
the
LEARNED/TX
indicator
stop flashing
and the learning mode is
cancelled
NOTES:
• If
the
codes
could
not
be
stored,
the
LEARNED/TX indicator
start flashing
rapidly
For
limited
number
of models,
codes
cannot
be
stored
in RC-925
• if the mode button
and LEARNED/TX
indicator
start
flashing
rapidly,
this
means
that
the
memory
is already f@l, and the code you have
iust attempted
to store was not stored
To "learn"
that code, first perform
the resetting
operation
(See page 21 )
The accessorious
remote control unit is equipped
with "system
call" function allowing
a series of remote
control
signals to be transmitted
by pressing a s_ngle button
This function
can be used for example
to turn on the am@fier's
power, select
the input source,
turn on the
monitor TV's power, turn on the source component's
power and set the source to the play mode, all at the touch
of a button
(1) System call buttons
Up
to 10 signals
each can
be
stored
at the
"CALL1 " and "CALL2"
buttons
I
1
_ilil _ _ &"i
(2) Storing system call signals
Press the power ON/SOURCE
button
and the
OFF button at the same time
• The LEARNED/TX
indicator flashes
_tE
%
Press the CALL I button
• The mode selector buttons
and LEARNED/TX
indicator
flash
Press the mode buttons
of the equipment
that
is to be registered
to System Call
4
Press the buttons whose remote
control signals
you want to store one by one
5
Repeat steps
3 and 4 to register the desired
buttons
Press the CALL1 or CALL2 button
and register
System Call
1
1
.--°
r,,_
_X23 _X22_
3
0 0 0
0
2,6
-_
6
NOTES:
• The
remote
control
signals
for the
buttons
pressed while storing the system call signals are
transmitted
when the buttons
are pressed,
so
cover the remote sensor or take other measures
so that the components
do not operate
while
the signals are being stored
• The mode button
and
LEARNED/TX
indicator
flashing
rapidly if you have ageady stored
the
maximum
number of signals
(3) Using
the
system
call function
Press
the button
at which
the
system
call sJgn@s
have been
stored
• The
stored
signals
are transmitted
successively
2O
Publicidad
