Metabo HPT FCJ 65V3 Instrucciones De Manejo página 6

English
SPECIFICATIONS
Model
Voltage (by areas)
Power input
Max. cutting depth
No-load speed
Stroke
Min. cutting radius
Weight (without cord)
* Be sure to check the nameplate on product as it is subject to change by areas.
STANDARD ACCESSORIES
(1) Blade No. 31 .................................................................1
For cutting thick lumber
(2) Splinter guard................................................................1
(3) Chip cover .....................................................................1
(4) Hexagonal bar wrench ..................................................1
Standard accessories are subject to change without notice.
OPTIONAL ACCESSORIES (sold separately)
(1) Blades, No.1 – No. 6, 31*
* No. 31 Blade is a standard accessory.
(2) Guide
Optional accessories are subject to change without notice.
APPLICATIONS
○ Cutting various lumber and pocket cutting
○ Cutting mild steel plate, aluminum plate, and copper
plate
○ Cutting synthetic resins, such as phenol resin and vinyl
chloride
○ Cutting thin and soft construction materials
PRIOR TO OPERATION
1. Power source
Ensure that the power source to be utilized conforms
to the power requirements specifi ed on the product
nameplate.
2. Power switch
Ensure that the power switch is in the OFF position. If the
plug is connected to a receptacle while the power switch
is in the ON position, the power tool will start operating
immediately, which could cause a serious accident.
3. Extension cord
When the work area is removed from the power source,
use an extension cord of suffi cient thickness and rated
capacity. The extension cord should be kept as short as
practicable.
MOUNTING THE BLADE
1. Use the accessory hexagonal bar wrench to loosen
the blade set screws on the blade holder, as shown in
Fig. 1(a).
2. Holding the blade with its cutting edge facing the front,
insert the mounting portion of the blade into the plunger
groove until it touches the bottom of the groove.
5
FCJ65V3
(110 V, 115 V, 120 V, 127 V, 220 V, 230 V, 240 V)
400 W*
Wood: 65 mm
Mild steel: 6 mm
0 – 3000/min
18 mm
25 mm
1.5 kg
3. As shown in Fig. 1(b), fi rmly clamp the side screw.
CAUTION
○ Loosened set screws may cause the blade to be
damaged. Always ensure that the set screws are securely
tightened. Always ensure that the plunger groove is clean
and clear of sawdust to ensure proper blade mounting
and set screw clamping.
4. Storing the hexagonal bar wrench
(1) Insert in a hole on the side of the main unit with
holding the short side horizontally as shown in
Fig. 2.
(2) Rotate with the hexagonal bar wrench inserted and
secure as shown in Fig. 2.
ADJUSTING THE GUIDE ROLLER
The guide roller, shown in Fig. 3, is employed to prevent
the blade from snapping. Prior to use, adjust guide roller in
accordance with the following procedures:
(1) Loosen the holder set screw with the accessory
hexagonal bar wrench.
(2) Gently slide the guide roller until the roller groove lightly
touches the back of the blade.
NOTE
On delivery from the factory, there is a gap of about 3mm
between the roller and blade.
(3) Firmly tighten the holder set screw.
CAUTION
○ The guide roller can be used only for Blades that have a
straight line on the rear that is longer than 50 mm. (Fig.
4A and 4B) When using other types of blades (Fig. 4C),
slide the guide roller in backwards so that the guide roller
does not contact the blade.
○ When cutting thick boards or performing continuous
cutting operations, use the blade shown in the Fig. 4A,
4B and be sure to set the guide roller.
CHIP COVER POSITIONING
1. Chip cover
Use the chip cover to reduce fl ying of cut particles and to
easily operate the saw.
Slide the chip cover while lightly pressing its front
section.
The chip cover can be set at three positions as shown in
Fig. 5.
2. How to choose the position of the ship cover
Set the chip cover to the fi rst step when attaching or
removing the blade.
Set the chip cover to the second step when cutting
wooden materials.
FCJ65S3
3000/min