care and maintenance
METAL PARTS (STRUCTURE)
This product has been made with resistant materials of the
highest quality. With correct care and maintenance you will
be able to enjoy it for many years. However, dirt or other
contaminants and bad use could damage it.
For the optimal conservation of pieces manufactured in
steel and stainless steel, especially if they are exposed to
the elements, periodic maintenance is advised.
For maximum resistance to corrosion, stainless steel
surfaces must always be kept clean. This maintenance
must be tailored to the conditions to which your product
is exposed (dust, dirt, humidity in combination with heat,
salty or potentially corrosive environments, etc.). This can
vary from one to four times a month, in normal settings,
or up to once a day in cases of unhygienic or very rough
conditions.
You must be the one who adjusts and evaluates the peri-
odicity of the maintenance according to how the material
reacts, increasing or reducing it depending on what is nec-
essary for proper product care. In any case, we recommend
cleaning it at least once a week, as a starting point.
Therefore, it's important to keep the product clean.
Please follow these simple instructions to keep the product
in good condition:
• For cleaning both steel and stainless steel, use only
a cloth dipped in warm water and mild soap. Never use
abrasive soaps or detergents, as they can leave scratches
and produce discoloration.
• Rub gently with a damp cloth. Rinse and wring the cloth
frequently, to keep it moist. Make sure to rinse well and dry
with another cloth.
• If the surface is glossy, you must wash it along the
grain, to avoid scratching the surface. On polished
surfaces, you must previously remove dust to avoid
scratching the surface.
• If the event of a spill, clean the stain as quickly as
possible.
• If you are unable to remove the stains with a damp
cloth, apply a metal cleaner (INOX-version stainless
steel cleaner) to the surface with a cloth. Read the
instructions for the cleaner carefully, and test it first on
an inconspicuous spot. Make sure to rinse well and dry
with another cloth.
• In the INOX version, to eliminate possible rust stains
that may appear due to a porosity defect, humidity, or
misuse, it is best to use a product directly to remove
rust spots.
When the product is extremely dirty, with stains,
incrustations, or signs of surface discoloration due
to long periods of neglect, or poor maintenance, we
recommend contacting professionals to restore the
surface's initial appearance.
HPL PARTS (FIELD)
HPL does not require special care.
• Clean with a cloth dampened in warm water and mild
soap.
• Never use abrasive soap or detergent, sandpaper or
steel wool since they could scratch the surface or make
colours fade.
• Never use furniture polish which contains wax, since
these kinds of products tend to leave a sticky layer on
the surface which attracts dust and dirt.
rs-barcelona.com
IROKO WOOD (LEGS AND HANDLES)
As a natural material, iroko can vary in colour, or even
crack due to humidity and sudden changes in tempera-
ture. Exposed to the elements, iroko undergoes a natural
oxidation process that affects its colour, taking on an
attractive silver- grey tone.
Iroko pieces should be treated with a waterproof sealer
to protect them from moisture and stains (provided they
are cleaned immediately). However, this sealant naturally
vanishes over time.
We recommend treating the wood with sealant every
three months, or more frequently at dining and hospitality
establishments. To restore iroko's original appearance,
sand the entire surface and apply the sealant, following
the manufacturer's instructions.
Never use soaps or abrasive detergents, or furniture
cleaning products containing wax, as these types of prod-
ucts form a sticky layer on the surface that attracts dirt.
IF THE PRODUCT IS USED OUTDOORS, KEEP IT CLEAN
AND IN GOOD CONDITION, FOLLOWING THESE
INSTRUCTIONS MORE FREQUENTLY.
WHEN THE PRODUCT IS KEPT OUTDOORS AND IS NOT
USED FOR PROLONGED PERIODS, WE RECOMMEND YOU
TO USE THE PROTECTIVE COVER.