Publicidad
Idiomas disponibles
Idiomas disponibles
General
Unpack the heater carefully and retain the packaging for possible
future use, in the event of moving or returning the fire to your supplier.
These models are designed to be free standing and are normally
positioned against a wall.
The fire incorporates a flame effect, which can be used with or without
heating, so that the comforting effect may be enjoyed at any time of
the year. Using the flame effect on its own only requires little electricity.
A choice of 1kW or 2kW heat output is provided by the fan heater,
which is located at the bottom of the unit.
Before connecting the heater check that the supply voltage is the
same as that stated on the heater.
Please note: Used in an environment
very low, it may be possible to hear a sound which is related to the
operation of the flame effect. This is normal and should not be a
cause for concern.
Electrical connection
WARNING – THIS APPLIANCE MUST BE EARTHED.
This heater must be used on an AC ~ supply only and the voltage
marked on the heater must correspond to the supply voltage.
Before switching on, please read the safety warnings and operating
instructions.
Controls
- see Fig. 2
These switches provide a choice of heat settings. The appliance is
in standby mode when the mainslead is plugged in. This is indicated
by the red neon behind the flame effect screen. The two selector
switches are in the ON position when the side with the markings on
(i.e. I, or II) is pushed in.
Selector switch 1 (
) Controls the electricity supply to the
appliance and flame effect. Press for 'ON' and
'Standby'. If both selector switches 2 and 3 are
in the OFF position, the product works on
flame effect only.
Selector Switch 2 (I) Provides 1kW heat output
Selector Switch 3 (II) Provides 2kW output with switch 2
Thermostat (T) - see Fig. 3
In order to maintain a certain room temperature, set the controller to
'max.'. Operate the appliance at full power until the required room
temperature is reached. Set back the thermostatic controller until the
appliance switches off with an audible "click". This temperature will be
kept almost constant by the thermostatic control switching on and off
automatically. Please note that the appliance can only be switched
on when the thermostat setting is higher then the room temperature.
Remote
control - see Fig. 4
The maximum range of use is ~ 15metres.
Warning: It takes time for the receiver to respond to the transmitter.
Do not press the buttons more than once within two seconds for
correct operation.
Battery information - see Fig. 4
1. To activate the remote control remove the battery isolation strip,
which is used to ensure your remote control reaches you fully charged.
2. To replace the remote control battery, turn over the remote control,
and follow the diagram embossed on the remote control
3. Only use CR2025 or CR2032 size of batteries.
where background noise is
Discard leaking batteries
Dispose of batteries in the proper manner according to provincial and
local regulations.
Any battery may leak electrolyte if mixed with a different battery type, if
inserted incorrectly, if all the batteries are not replaced at the same time,
if disposed of in a fire, or if an attempt is made to charge a battery not
intended to be recharged.
Maintenance
WARNING: ALWAYS DISCONNECT FROM THE POWER SUPPLY
BEFORE ATTEMPTING ANY MAINTENANCE.
Light Emitting Diode
This fire is fitted with LED (Light Emitting Diode) lamps. These LED
lamps are maintenance-free and should not require replacing during
the life of the product.
Thermal Safety Cut-out
The built-in overheat cut-out switches off the appliance automatically in
the event of a fault. If this occurs switch off the appliance or disconnect
the mains plug from the socket. After a short cooling down phase, the
appliance is ready for use again. If the fault should occur again, see
your local dealer.
Cleaning
WARNING – ALWAYS DISCONNECT FROM THE POWER SUPPLY
BEFORE CLEANING THE HEATER.
For general cleaning use a soft clean duster – never use abrasive
cleaners. The glass viewing screen should be cleaned carefully with a
soft cloth. DO NOT use proprietary glass cleaners.
To remove any accumulation of dust or fluff the soft brush attachment of
a vacuum cleaner should occasionally be used to clean the outlet grille
of the fan heater.
Recycling
For electrical products sold within the European Community.
At the end of the electrical products useful life it should not
be disposed of with household waste. Please recycle where
facilities exist. Check with your Local Authority or retailer for
recycling advice in your country.
After Sales Service
Should you require after sales service or should you need to purchase
any spares, please contact the retailer from whom the appliance was
purchased or contact the service number relevant to your country on
the warranty card.
Please do not return a faulty product to us in the first instance as
this may result in loss or damage and delay in providing you with a
satisfactory service. Please retain your receipt as proof of purchase.
Publicidad
