Important Safety Notes - Martin Yale intimus 100SP2 Instrucciones De Uso

GB

IMPORTANT SAFETY NOTES

<< The machine may not be operated by more
than one person at any given time!
The machine was designed for safe operation
by "one person only".
<< During the shredding process no other
work may be performed on the machine
(for example cleaning, etc.)!
<< The machine is not a toy, and is not suitable
for use by children!
The overall technical safety concept of
this machine (dimensions, feed openings,
emergency shutdown devices etc.) does not
provide for any guarantee regarding hazard-
free operation by children.
CONTROLS:
1 = Pushbutton switch (fig. 1)
"Ready"/ "Off" / "Stop"
This button has three functions:
a) "Ready"
The machine changes to "Ready" if you
press this button briefly.
b) "Off"
The machine switches off if it is in the
"Ready" mode and the button is held
down for about 3 seconds.
Note: The machine
automatically if it is not used for about 5
minutes.
c) "Stop"
If you press this button briefly when the
cutters are running they switch off and
stop.
2 = Light barrier (forward operation) (fig. 2)
The shredding operation is started as soon
as a sheet of paper passes through the feed
slot.
3 = Pushbutton switch „reverse" (fig. 1)
Pressing this button activates the cutting
mechanism into reverse.
4 = Pilot lamp „ready" (fig. 1)
Lights when the pushbutton switch (1) is
operated.
5 = Pilot lamp
„receptacle full" / „door open" (fig. 1)
Lights when
5 4 6
fig. 1
<< Danger of injury! Never insert fingers into
<< In case of danger switch the machine off
<< Always unplug the machine from the
OPERATION
a) the receptacle is full and needs to be
emptied. At the same time the machine
switches off automatically.
b) the door is not closed. The machine then
switches off automatically and it cannot be
started as long as the door is open.
6 = Pilot lamp „paper jam" (fig. 1)
Lights when too much paper is fed to the
cutters. The cutting system blocks and stops.
The motor is switched off.
switches off FEEDING OF SHEETS:
- Turn machine on with pushbutton switch (1)
(fig. 1). Pilot lamp lights up (4) (fig. 1).
- Feed paper through the inlet guide to the cutting
system.
- Machine switches automatically to forward
and draws paper in. The machine switches off
automatically after shredding.
Note: In order to always obtain a correct cutting
result in terms of particle size and thus achieve
the safety class according to DIN 32757 as
stated in the brochure, the material to be cut
must always be fed into the cutting mechanism
at a right angle to the cutting mechanism and in
appropriate quantities in the middle of the inlet
slot.
Never feed the shredder with a quantity
of paper exceeding the maximum indi-
cated in the technical details!
Should the machine be overfed, follow the
instructions under „PAPER JAM".
1 3
<< Danger of injury! Keep all
loose articles of clothing, ties,
jewelery, long hair or other loose
objects away from opening!
opening!
with the mains switch, or with the emer-
gency switch, or unplug the machine!
mains power supply before opening the
machine!
Repairs may only be performed by trained
personnel!
2
fig. 2
4
INITIATION
SCOPE OF APPLICATION:
The document shredder intimus 100SP2/CP4/
CP5/CP6/CP7 is a machine for the destruction
of common written material.
The machine may only be used to
shred paper!
Shredding of other types of data carriers
and also of staples and paper clips with
the models with cutting width 0.8x12 mm
(CP6) or 0.8x4.5 mm (CP7) may lead to
injuries (for example due to splintering of
hard materials etc.) and damage to the
machine (for example destruction of the
cutter etc.).
INSTALLATION:
- Unpack and set machine upright.
- Place plastic sack into the receptacle.
- Plug in the machine (for instructions for the
necessary precautions see „TECHNICAL
DATA".
The air vents in the housing are ne-
cessary for cooling and may not be
covered or closed!
The mains connection at the machine
must be freely accessible!
Only operate the machine in enclosed
rooms at temperatures between 10°C
and 25°C!
OPERATION
EMPTYING THE COLLECTING BAG (fig. 3):
When the collecting bag is full, the machine turns
off automatically. The pilot lamp (5) (fig. 1) lights
up. Empty the collecting bag as follows:
- Open the door and take out the sliding frame
with the collecting bag.
- Remove the rubber band, take out the full bag
and dispose of contents.
- Put the empty bag from below through the sliding
frame and put the edges of the bag approx. 10
cm over the frame outwardly.
- Move back the sliding frame with the collecting
bag and close door. The pilot lamp (5) (fig. 1)
goes off.
Note: The machine will only run with closed
door!
fig. 3