Inglesina APTICA Manual De Instrucciones página 36

CARRYCOT VENTILATION
La culla Aptica è dotata di un sistema coordinato
di aerazione.
fig. 50 L'aerazione del fondo può essere regolata
agendo sulla leva (V) posta anteriormente.
fig. 51 Se presenti: I due inserti in rete sul
retro e sulla capotta consentono una maggior
circolazione dell'aria all'interno della culla.
MATTRESS AND INTERNAL LINING MAINTENANCE
It is advisable to remove the mattress and internal lining
periodically for correct maintenance.
fig. 52 To remove the internal lining simply release it from
the edge of the carrycot.
CARRYCOT LINING MAINTENANCE
fig. 53 When refitting the carrycot lining removed
previously, ensure that the two elastic loops (X1) are fitted
perfectly underneath the lower tabs (X2) on both the
attachment devices.
Caution! Incorrect positioning of the elastic loops could
interfere with correct attachment of the carrycot to the
chassis.
STROLLER SEAT
ATTACHING THE STROLLER SEAT TO THE CHASSIS
fig. 54 Attach the stroller seat (H) to the chassis,
positioning it in the dedicated housings on both sides of the
structure.
fig. 55 Caution: ensure that the stroller seat is always
attached correctly on both sides before use.
fig. 56 The stroller seat can be used both rear facing and
forward facing.
DETACHING THE STROLLER SEAT FROM THE CHASSIS
fig. 57 Operate the lever (H1) and simultaneously lift the
stroller seat from the chassis.
Caution: do not, under any circumstance, carry out this
operation with the baby inside.
ADJUSTING THE BACKREST
fig. 58 The backrest can be adjusted to 7 positions; use
the central device (H2) and bring the backrest to the desired
position.
ADJUSTING THE FOOTREST
fig. 59 To lower the footrest, use both levers (H3)
positioned on the lower part and simultaneously press them
downwards.
fig. 60 To lift the footrest, simply pull it upwards and it
shall automatically lock into position.
The footrest can also be extended further to follow your
child's growth.
SAFETY BELTS
fig. 61 Ensure that the safety belts are inserted in the
eyelets at the height of the shoulders or immediately above.
If the position is not correct, remove the belts from the first
pair of eyelets and reinsert them in the second one; always
use eyelets at the same height.
fig. 62 Make sure that the back strap is properly inserted
in the ends of the waist one.
fig. 63 Fasten the ends of the strap belt to the central
buckle.
fig. 64 The waist strap must always pass through the side
loops (H4) and, when being used, it must be adjusted in
order to properly secure the baby.
fig. 65 Always use the crotch strap together with the waist
one, adjusting both of them properly.
Caution! Failure to comply with this precaution can cause
36
the baby to fall or slide out, with serious injury risks.
ATTACHING THE HANDRAIL
fig. 66 To attach the bumper bar (I), press the buttons (I1)
and attach it in the dedicated housings (I2) in the stroller
seat.
fig. 67 The handrail can be open on one side or fully
removed; to open it, press the button (I1) and remove it from
its housing; to remove it, repeat the procedure on the other
side.
ATTACHING THE STROLLER HOOD
fig. 68 The hood (J) is mounted onto the stroller by
positioning it in correspondence of the 2 housings (J1) on
the pushchair seat and inserting the slides (J2), pushing until
they both click into place.
fig. 69 Fasten the press studs of the lining to the backrest,
starting with the upper ones (J3) and then with the lower
ones (J4).
fig. 70 To adjust the hood, simply accompany it to the
desired position.
fig. 71 The hood features an additional fabric insert
and sun shade that extend the degree of cover, improving
protection from the sun.
DETACHING THE HOOD FROM THE STROLLER
fig. 72 To remove the hood (J) from the stroller seat,
detach the press studs (J3/J4) that hold the lining on the
backrest.
fig. 73 Then operate the levers (J5) and simultaneously
pull the hood out from the housings (J1) on the stroller seat.
HOOD LINING MAINTENANCE
The hood lining can be removed to allow for its correct
maintenance.
fig. 74 Release the buttons (J6) on both the hood joints
(J7).
fig. 75 Then detach the thicker front band (J8) and the
thinner rear band (J9) from the side joints (J7) and completely
remove the lining.
fig. 76 To refit the lining, insert the thicker front band (J8)
and the thinner rear band (J9) in the dedicated guides inside
the lining.
fig. 77 Finally, insert the bands (J8/J9) in the side joints
(J7), pushing them correctly into their housings, and fasten
both the side press studs (J6).
CLOSING THE CHASSIS WITH THE STROLLER SEAT
ATTACHED (STROLLER CONFIGURATION)
The chassis can be closed with the stroller seat attached,
both rear facing and forward facing.
fig. 78 Facing the parents: before closing the stroller,
lift the footrest completely, fold the hood and recline the
backrest to its most horizontal position. Then proceed to
close as specified previously (fig. 18/19/20).
fig. 79 Caution! Once closed, check that the footrest is
always positioned internally with respect to the chassis
handlebar.
fig. 80 Facing the world: before closing the stroller, fold
the hood and bring it completely forwards. Then proceed to
close as specified previously (fig. 18/19/20).
STROLLER SEAT LINING MAINTENANCE
It is recommended to remove the lining periodically to
provide for its correct maintenance.
fig. 81 Detach the two lower bands (H5) from the footrest.
fig. 82 Remove the sides of the stroller seat detaching first
the two front corners from the relevant hooks (H6), then the
two side bands (H7) that fix the lining to the backrest.
fig. 83 Detach the four rear press studs (H8) from the
backrest structure.
fig. 84 Remove the waist strap from the side loops (H4),