Technical Characteristics - Nice F210B Instrucciones Y Advertencias Para El Instalador

5) Testing and operational control
After the recognition phase make sure that the Led on the photocell flashes (both on the TX and on the RX). Check the status of the photocell on table 2 based
on the type of flash of the Led "L".
Table 2
LED "L"
L Off
3 fast flashes and
1second pause
Very slow flashing
Slow flashing
Fast flashing
Very fast flashing
Always on
Warning: testing of the entire automation must be performed again in accor-
dance with that foreseen in the related installation manuals after photocells
have been added or replaced.
To check the photocells and to make sure that there is no interference with
other devices, pass a 5 cm diameter, 30 cm long cylinder on the optical axis,
first near TX, then near RX and finally at the mid-point between them (see Fig-
ure 15) and make sure that in all these cases the device is triggered, switch-
ing from the active to the alarm status and vice-versa. Finally, make sure that
6) Maintenance
The photocell does not require any particular maintenance, however a control
should be performed at least once every six months to check its integrity
(presence of dampness, rust, etc), as well as cleaning of the external casing
and lenses and testing as described in the previous paragraph. The F210B
6.1) Disposal
As for the installation, the disposal of the product, at the end of its effective
life, must be performed by qualified personnel. This product is made of vari-
ous types of material, some of which can be recycled while others must be
disposed of. Enquire about the recycling or disposal systems available for this
product category in compliance with regulations locally in force
Warning: some parts of the product may contain polluting or hazardous sub-
stances that, if incorrectly disposed of, could have a damaging effect on the
environment or on the health of individuals.

7) Technical characteristics

In order to improve its products, NICE S.p.a. reserves the right to modify the technical characteristics at any time without prior notice. In any case, the
manufacturer guarantees their functionality and fitness for the intended purposes.
Note: all technical characteristics refer to a temperature of 20°C.
F210B directional photocell
Product type
Adopted technology
Power supply/output
Absorbed power
Detection capacity
TX transmission angle
RX reception angle
Adjustability of the F210B photocell
Useful range
Maximum range
Maximum length of cable
Addressing capability
Use in acid, saline or potentially
explosive atmosphere
Assembly
Casing protection class
Operating temperature
Dimensions / weight
Status
The photocell is either
disconnected or malfunctioning
Device not recognised by the
control unit
The TX transmits properly
The RX receives a perfect signal
The RX receives a fair signal
The RX receives a weak signal
The RX receives a very poor
signal
The RX does not receive any
signal
Presence detector for automatic gate and door automation systems (type D according to EN standard 12453),
consisting in a "TX" transmitter and "RX" receiver.
TX-RX direct optical interpolation with modulated infrared beam
The device can be connected to "BlueBus" networks only from which it obtains its power supply and sends
output signals.
1 BlueBus unit
Opaque objects located on the optical axis between TX and RX, larger than 50 mm and moving slower than 1.6m/s
+/- 4° (value taken at 50% of the capacity)
+/- 3° (value taken at 50% of the capacity)
Approximately 210° on the horizontal axis and 30° on the vertical axis
10m or 30m with the ">10m" jumper cut for maximum TX-RX misalignment ± 2° (the range may be further
reduced in the presence of particularly intense atmospheric conditions: fog, rain, snow, dust, etc.)
20m or 60m with the ">10m" jumper cut for maximum TX-RX misalignment ± 2°
(capacity guaranteed under optimal conditions)
Up to 50m
Up to 7 detectors with safety function and 2 with open command function.
The automatic synchronism prevents interference between the various detectors .
No
Vertically wall mounted or on "MOCF" posts with "FA2" bracket.
IP44
20÷55°C
46 x 128 h 45mm / 230 g
Action
Check that a voltage of approximately 8-12 Vdc is present on the
photocell terminals. If the voltage is correct the photocell is probably
malfunctioning
Repeat the recognition phase from the control unit, making sure that all
photocell pairs have different addresses
Normal operation
Normal operation
Normal operation but the the TX-RX alignment should be checked as
well as the cleanness of the glasses
It is at the limit of normal operation, the TX-RX alignment should be
checked as well as the cleanness of the glasses
Make sure that the LED on the TX flashes very slowly. Check to see if
there is an obstacle between TX and RX. Check the TX-RX alignment
the the intended action occurs in the control unit, for example that it causes
the reversal of the movement during the closing manoeuvre.
The control of the F210B optical presence sensor (type D) according to the
EN 12445 standard, is performed with the 700x300x200mm test paral-
lelepiped with 3 black sides and 3 polished white or mirrored sides as indi-
cated in figure 16 and according to chapter 7 of the EN 12445:2000 standard
(or enclosure A of prEN12445:2005).
photocell has been designed to function under normal conditions for at least
10 years, therefore maintenance should be performed more frequently once
this period has expired.
As indicated by the symbol in figure 17, this product
must not be disposed of along with household
waste. Perform "separated collection" for disposal in
compliance with regulations locally in force, or return
the product to the manufacturer when purchasing a
replacement.
Heavy fines may be imposed by local laws for the illegal disposal of this prod-
uct.
GB
17
3