Chicco Auto-FIX FAST Instrucciones De Uso página 16

Diag. 3 (Profile)
K. Abdominal car safety belt slot on the
child car seat
L. Abdominal car safety belt slot on the base
M. Buttons to rotate the carry handle
N. Clik Clak pins (to fasten it to the stroller)
Diag. 4 (Back)
O. Release handle (from the base and the
stroller)
P. Diagonal car safety belt slot
Q. Belt threading slots
R. Slot elements for the child car seat har-
ness straps
S. Stabiliser block
(*) Shape and model can differ according
to the child car seat version being used.
(**) Optional
1.4 POSITIONS OF THE HANDLE
The child car seat carry handle can be ad-
justed to 4 positions (Diag. 5)
A. Position when travelling by car (WARN-
ING: this is the only position allowed
when travelling by car).
B. Position when carried by hand.
C. Rocker chair mode position or when
you need to fasten it to an appropriate
Chicco stroller.
D. Fixed rocker chair position.
To adjust the position, press both buttons
(M) on the handle bar together and rotate
it to the desired position until you hear it
click into place.
1.5 RESTRICTIONS AND REQUISITES
REGARDING THE USE OF THE PROD-
UCT AND CAR SEAT
WARNING! Read these restrictions and
requisites carefully to ensure the product
and car seat are used safely: if you don't,
the safety levels cannot be guaranteed.
• The child car seat can be fitted onto the
front passenger seat or any other back
seats. In any case the vehicle seat must
be facing forwards. Never use this child
car seat on vehicle seats which are fac-
ing sideways or facing rearwards (diag. 6)
• The vehicle seat must be fitted with a
3-point static or 3-point retractor safety
belts approved to UN/ECE Regulation
No.16, or other equivalent standards
(Diag. 7).
• WARNING! Never fit the child car seat to
a vehicle seat that is only equipped with a
2-point safety belt (Diag. 8)
• Never use the booster cushion if the child
weighs more than 6 kg.
2. CAR INSTALLATION
The child car seat can be installed with or
without the base (optional). In both cases,
the child car seat must always be installed
facing rearwards.
2.1 INITIAL CONFIGURATION OF
THE HARNESS STRAPS AND
SHOULDER PADS
The child car seat is fitted with 2 different
types of shoulder straps (A and B) accord-
ing to the version being used. Before using
the child car seat, assemble the shoulder
straps as follows:
• Shoulder straps version A (Diag. 9A, 9B
and 9C): thread the harness straps through
the slots in the fabric cover (not through
the seat structure below) so that they are
visible on the seat. Thread the harness
buckle through the crotch pad.
• Shoulder straps version B (Diag. 10A and
10B): thread the harness straps though
the two shoulder pads. Thread the harness
buckle through the crotch pad.
2.2 INSTALLATION WITH THE BASE
To install the child car seat with base on the
vehicle seat, proceed as follows:
1. Remove the child car seat from the base
by pulling the release lever behind the
backrest whilst using the carry handle
to lift it upwards (Diag. 11).
2. Position the base on the chosen vehicle
seat, position it as seen in Diag. 12 so
that it touches the vehicle seat backrest.
3. Pull the vehicle safety belt and connect
it to the relative buckle, threading the
abdominal belt through the two slots (L)
indicated by the light blue arrows; pull it
as tight as possible (Diag. 13).
4. Before attaching the child car seat onto
the base, check that the stabiliser block
is closed (Diag. 14).
5. Attach the child car seat onto the base
16