Publicidad
WARNING: Never use the heater without first
assembling all the components correctly and
making sure the heater is positioned on a perfectly
flat, stable and level surface.
►►5.1. SWITCH-ON:
►5.1.1. Connect the heater's plug to the mains (Pic. 6).
►5.1.2. Turn the power selector to the desired mode
(Pic. 7). Here are the available settings:
• By setting the power selector to " " the heater will only
operate in ventilation mode.
• By setting the power selector to "I" the heater will
operate at heating power 1.
• By setting the power selector to "II" the heater will
operate at heating power 2.
• By setting the power selector to "III" the heater will
operate at heating power 3 (if present).
CAUTION: A SERIES OF SENSORS CHECK THAT
THE HEATER IS OPERATING CORRECTLY AND
STOPS THE APPLIANCE IN THE EVENT OF A
SERIOUS FAULT. THE HEATER WILL NOT RESUME
OPERATION AUTOMATICALLY, THIS MUST BE
PERFORMED MANUALLY. WAIT FOR THE HEATER
TO COOL DOWN COMPLETELY AND REMOVE
ANYTHING WHICH MIGHT HAVE BLOCKED THE
HEATER
(E.G.
OBSTRUCTED
IMPAIRED THE AIR SUPPLY, ETC.) AND PRESS THE
"RESET" BUTTON ALL THE WAY DOWN (Pic. 8).
MAKE SURE THE "BLOCKED HEATER INDICATOR
(1 Pic. 5)" TURNS OFF. IF, AFTER A FEW ATTEMPTS
TO RESUME OPERATION, THE HEATER DOES
NOT WORK, CONTACT THE TECHNICAL SUPPORT
SERVICE.
►►8. TROUBLESHOOTING
PROBLEM
POSSIBLE CAUSE
The heater
1. Power selector set to "0/OFF"
doesn't work
2. Incorrect connection or setting
of the room thermostat
3. No power supply
4. Blocked heater
The motor
1. Faulty motor
doesn't work
2. Blocked fan
The heater
1. Power selector set to
doesn't heat
"VENTILATION"
2. Faulty internal appliance
Reduced
1. Obstructed air vent
airflow
2. Faulty motor
►►5.2. SWITCH-OFF:
►5.2.1. Set the power selector to "0/OFF" (Pic. 9) and
leave the fan working until the heater fully turns off.
►5.2.2. Disconnect the heater from the mains power
supply (Pic. 10).
CAUTION: AVOID DISCONNECTING THE HEATER
FROM
COMPLETELY
SERIOUS DAMAGE.
►►6. STORAGE
Always disconnect the heater from the mains power
supply (Pic. 10) when not in use and wait a few minutes
for it to cool down completely before putting it away. Put
it back in a dry place and protected from dust. When the
heater is used again, check the condition of the power
supply cable. If in doubt regarding its state, contact the
technical support centre. Have the technical support
centre check that the heater is working properly at least
once a year and/or as required.
►►7. CONNECTING THE REMOTE ROOM
THERMOSTAT
In models with a remote room thermostat connection
(Pic.11), remove the plug connected to the heater and
connect the remote room thermostat (optional) (Pic. 12).
AN
AIR
VENT,
To ensure the heater works correctly, with the remote room
thermostat connected, set the ambient thermostat knob
(3 Pic. 5) located on the control panel to the maximum
temperature and only use the remote room thermostat.
CAUTION: TO ENSURE CORRECT OPERATION, THE
HEATER MUST HAVE EITHER THE PLUG COVER
(Pic. 13) OR THE REMOTE ROOM THERMOSTAT (Pic.
14), OTHERWISE THE HEATER WILL NOT TURN ON
(Pic. 15).
1. Turn the power selector to the desired mode
2a. Insert the room thermostat's plug correctly
2b. Make sure the temperature set on the room thermostat is
higher than the outdoor temperature
2c. Make sure the cap of the thermostat outlet is inserted
correctly
3a. Insert the power supply cable correctly
3b. Make sure your mains power supply is working correctly
3c. Contact a support centre
4a. Reset the heater
4b. Contact a support centre
1. Contact the support centre
2a. Remove any obstructions
2b. Contact the support centre
1. Turn the power selector to the desired heating power
2. Contact the support centre
1a. Remove any obstructions
1b. Contact the support centre
2. Contact the support centre
THE
MAINS
BEFORE
STOPPED
MOVING
POSSIBLE SOLUTION
en
it
de
THE
FAN
HAS
es
TO
AVOID
fr
nl
pt
da
fi
no
sv
pl
ru
cs
hu
sl
tr
hr
lt
lv
et
ro
sk
bg
uk
bs
el
zh
Publicidad
