Function Settings - Mitsubishi Electric Mr.Slim PLA-RP BA Serie Manual De Instalación

6. Electrical work
Service menu
Test run
Input maintenance info.
Function setting
Check
Self check
Main menu:
Cursor
F1 F2 F3 F4
Fig. 6-5
Function setting
Ref. address Grp.
Mode 1
Mode 2
Mode 3
Mode 4
Request:
Cursor Cursor
F1 F2 F3 F4
Fig. 6-7
Function setting
Ref. address Grp.
Sending data
F1 F2 F3 F4
Fig. 6-
Note:
• Make the above settings on Mr. Slim units as necessary.
• Table 1 summarizes the setting options for each mode number. Refer to the indoor unit Installation Manual for the detailed information about initial settings,
mode numbers, and setting numbers for the indoor units.
• Be sure to write down the settings for all functions if any of the initial settings has been changed after the completion of installation work.
Table1. Function setting options
Mode No. Mode
01 Automatic recovery after power
failure
02 Thermistor selection
(indoor temperature detection)
03 LOSSNAY connection
04 Power voltage
07 Filter sign
08 Fan speed
09 Outlet
10 Optional parts
(High-efficiency filter)
11 Vane
10
Function setting
Ref. address
Unit No.
Grp./1/2/3/4/All
Monitor:
Cursor Address
F1 F2 F3 F4
Fig. 6-6
Function setting
Ref. address Unit # 1
Mode 1
Mode 2
Mode 3
Mode 4
Request:
Cursor Cursor
F1 F2 F3 F4
Fig. 6-8
Settings
Disable
Enable (Four minutes of standby time is required after the restoration of power.)
Average temperature reading of the indoor units in operation
Thermistor on the indoor unit to which the remote controller is connected (fixed)
Built-in sensor on the remote controller
Not connected
Connected (without outdoor air intake by the indoor units)
Connected (with outdoor air intake by the indoor units)
240 V
220 V, 230 V
100 hours
2500 hours
Not displayed
Silent mode (or standard)
Standard (or High ceiling 1)
High ceiling (or High ceiling 2)
4 directional
3 directional
2 directional
No
Yes
No vanes (or the vane setting No.3 is effective.)
Equipped with vanes (The vane setting No.1 is effective.)
Equipped with vanes (The vane setting No.2 is effective.)

6.3. Function settings

6.3.1. Function setting on the unit (Selecting the unit functions)
1) For wired remote controller
1 (Fig. 6-5)
• Select "Service" from the Main menu, and press the [SELECT] button.
• Select "Function settings" with the [F1] or [F2] button, and press the [SELECT]
button.
2 (Fig. 6-6)
• Set the indoor unit refrigerant addresses and unit numbers with the [F1]
through [F4] buttons, and then press the [SELECT] button to confirm the cur-
rent setting.
<Checking the Indoor unit No.>
When the [SELECT] button is pressed, the target indoor unit will start fan opera-
tion. If the unit is common or when running all units, all indoor units for the se-
lected refrigerant address will start fan operation.
3 (Fig. 6-7)
• When data collection from the indoor units is completed, the current settings
appears highlighted. Non-highlighted items indicate that no function settings
are made. Screen appearance varies depending on the "Unit No." setting.
4 (Fig. 6-8)
• Use the [F1] or [F2] button to move the cursor to select the mode number, and
change the setting number with the [F3] or [F4] button.
5 (Fig. 6-9)
• When the settings are completed, press the [SELECT] button to send the set-
ting data from the remote controller to the indoor units.
• When the transmission is successfully completed, the screen will return to the
Function setting screen.
Setting No. Unit numbers
1 Set "Grp." for the Unit number.
These settings apply to all the
2
connected indoor units.
1
2
3
1
2
3
1
2
1 Set "1, 2, 3, 4, or All" for the Unit
number.
2
These settings apply to each
3
indoor unit.
• If "1, 2, 3, or 4" is set for the
1
Unit number, the settings ap-
2
ply only to the specified indoor
unit regardless of the number
3
of connected indoor units (one
1
through four units).
2
• If "ALL" is set for the Unit
number, the settings apply to
3
all the connected indoor units
1
regardless of the number of
connected indoor units (one
2
through four units).
1
2
3