Extension Cords - Black+Decker BDERO100 Manual De Instrucciones

14 • ENGLISH
making any adjustments, changing accessories,
or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power
tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
6. Electrical safety
Your tool is double insulated; therefore no earth
wire is required. Always check that the main
voltage corresponds to the voltage on the rating
plate.
Warning! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
BLACK+DECKER Service Center or an equally
qualified person in order to avoid damage or
injury. If the power cord is replaced by an equally
qualified person, but not authorized by
BLACK+DECKER, the warranty will not be valid.
7. Labels on tool
The label on your tool may include the following
symbols:
A ........
Read
Instructions
Hz .......
Manual
W ........
Use Eye
Protection
min .....
Use Ear
.....
Protection
.....
Use proper
respiratory
protection
n .......
0
V ........ Volts
FEATURES (Fig. A)
1. On/off switch
2. Sanding pad
3. Dust port
4. Canister
Amperes
...... Class II
Construction
Hertz
.... Earthing
Watts
Terminal
minutes
.... Safety Alert
Symbol
Alternating
Current
.../min.. Revolutions
or Recipro-
Direct
cation per
Current
minute
No-Load
OPM.... Orbits per
Speed
minute
SAFETY WARNINGS AND
INSTRUCTIONS: SANDERS
f ALWAYS WEAR EYE PROTECTION.
f Clean your tool out periodically.
Warning! Some dust created by power sanding,
sawing, grinding, drilling, and other construction
activities contains chemicals known to the State
of California to cause cancer, birth defects or
other reproductive harm. Some examples of these
chemicals are:
f lead from lead-based paints,
f crystalline silica from bricks and cement and other
masonry products, and
f arsenic and chromium from chemically- treated
lumber.
Your risk from these exposures varies, depending on how
often you do this type of work. To reduce your exposure to
these chemicals: work in a well ventilated area, and work with
approved safety equipment, such as those dust masks that
are specially designed to filter out microscopic particles.
f Avoid prolonged contact with dust from power
sanding, sawing, grinding, drilling, and other
construction activities. Wear protective clothing
and wash exposed areas with soap and water.
Allowing dust to get into your mouth, eyes, or lay on
the skin may promote absorption of harmful chemicals.
Caution! Wear appropriate hearing protection
during use. Under some condi- tions and duration
of use, noise from this product may contribute to
hearing loss.

Extension cords

When using an extension cord, be sure to use one heavy
enough to carry the current your product will draw. An
undersized cord will cause a drop in line voltage resulting
in loss of power and overheating. The following table
shows the correct size to use depending on cord length
and nameplate ampere rating. If in doubt, use the next
heavier gage. The smaller the gage number, the heavier
the cord.
Minimum Gage for Cord Sets
Volts
120V 0-25
240V 0-50
AmpereRating
American Wire Gage
More Not more
Than Than
0 - 6 18
6 - 10 18
10 - 12 16
12 - 16 14
Total Length of Cord in Feet
26-50 51-100 101-150
51-100 101-200 201-300
16 16 14
16 14 12
16 14 12
12 Not Recommended