Black and Decker GL360 Manual De Instrucciones página 16

16 • EnGLIsH
AssEMBLy
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Attaching the second handle (Fig. B)
► Slide the second handle (5) on to the main handle (2)
in an upwards direction.
► Secure the second handle in place with the two screws
provided.
Fitting the guard (Fig. C)
► Place the guard onto the tool as shown.
► Firmly press the guard (6) until it snaps into place.
► Secure the guard with the screw.
Warning! Never use the tool unless the guard is
properly fitted.
releasing the cutting line
In transit, the cutting line is taped to the spool housing.
► Remove the tape holding the cutting line (8) to the
spool housing (9).
Connecting the tool to the mains (Fig. D)
► Connect the female plug of a suitable extension cable
to the power inlet (4).
► Loop the cable through the cable restraint (3).
► Insert the mains plug into a mains outlet.
For wired in cable units: Make sure the cable is looped
through the cable restraint prior to connecting the plug to
the mains outlet.
Warning! The extension cable must be suitable for
outdoor use.
UsE
Warning! Let the tool work at its own pace. Do not
overload.
switching on and off
► To switch the tool on, squeeze the trigger lever (1).
► To switch the tool off, release the trigger lever.
Warning! Never attempt to lock the trigger lever in the
on position.
HInts For oPtIMUM UsE
General
► In order to achieve optimum cutting results, only cut dry
grass.
trimming
► Hold the tool as shown in Fig. D.
► Gently swing the trimmer from side to side.
► When cutting long grass, work in stages from the top.
Take small cuts.
► Keep the tool away from hard objects and delicate
plants.
► Cutting line will wear faster and require more feeding if
the cutting is done along pavements or other abrasive
surfaces or heavier weeds are being cut.
► As you use the trimmer, the string will get shorter due
to wear. Gently bump the unit on the ground whilst
running and the line will feed.
► If the tool starts running slowly, reduce the load.
Fitting a new spool of cutting line (Fig. E and F)
Replacement spools of cutting line are available from your
Black & Decker dealer. Catalog number: rs-136.
► Keep the tabs (12) depressed and remove the spool
cover (13) from the housing (9).
► Remove the empty spool (14) from the spool housing.
► Remove any dirt and grass from the spool cover and
housing.
► Take the new spool and unwind approximately 10cm
of cutting line.
► Feed the cutting line through the eyelet (15).
► Push the spool onto the drive shaft (16) and rotate it
slightly until it is seated. Make sure that the cutting line
is not trapped under the spool and that 10cm of cutting
line protrudes from the housing.
► Align the tabs (12) on the spool cover with the holes in
the housing (15).
► Push the cover onto the housing until it snaps securely
into place.
Warning! If the cutting line protrudes beyond the
trimming blade (7), cut it off so that it just reaches the blade.
Winding a new cutting line onto an empty spool
(Figs. G, H and I)
You may wind new cutting line onto an empty spool.
Catalog number: rs-136.
► Remove the empty spool from the tool as described
above.
► Remove any remaining cutting line from the spool.
► Feed 2cm of cutting line into one of the holes (17) in
the spool as shown.
► Wind the cutting line onto the spool in the direction of
the arrow (18). Make sure to wind the line on neatly
and in layers. Do not criss-cross.
► Let the line protrude approximately 10cm from the
spool and hold a finger on the line to keep it in place.
► Proceed as described above to fit the spool on the tool.
Warning! Only use the appropriate type of Black & Decker
cutting line.