Fc.Y. 1 = Lit If Gate Is Not Closed + Duration Tcy - Key Automation CT202 Instrucciones Y Advertencias Para Su Instalación Y Uso

EN
6 - FURTHER DETAILS - ADVANCED MENU
The ADVANCED MENU allows the system to be further customised
by modifying parameters not accessible from the basic menu
To access the ADVANCED menu, press the MENU key and hold it
PARAMETERS
EL.F.
1
SP.h.
2
Ph.2.
3
tP.h.
4
n
ed.M.
5
iE.D.
6
tE.D.
7
LP.o.
8
TP.C.
9
FP.r.
10
tP.r.
11
FC.Y.
12
tC.Y.
13
dE.A.
14
se.r.
15
se.f.
16
HA.o.
17
HA.c.
18
n
mp.r.
19
de.f.
20
To set the default values: 1) access the advanced programming
function; 2) select the "dEf" parameter"; 3) activate the modification
mode ("0" on display"); 4) accept the modification (press "MENU"
24
DESCRIPTION
Electric brake
0 = disabled
1 = enabled
PHOTO1 response on start-up from closed
0 = PHOTO1 check
1 = the gate also opens if PHOTO1 is engaged
PHOTO2 response
0 = Enabled in opening and closing OP/CL
1 = Enabled only in opening OP
Photo device test
0 = disabled
1 = PHOTO1 enabled
2 = PHOTO1 enabled
3 = PHOTO1 and PHOTO2 enabled
Type of edge
0 = contact (NC)
1 = resistive (82k)
Edge intervention mode
0 = intervenes only on closing with inversion of direction
1 = stops automation (on opening and closing) and releases
the obstacle (short inversion)
Edge test
0 = disabled
1 = enabled
Pedestrian opening
Automatic reclosing time from pedestrian (0 = disabled)
Flashing light output configuration
0 = Steady
1 = Flashing
Pre-flash time
(0 = disabled)
Courtesy light configuration
0 = At end of manoeuvre, lit for time TCY
1 = Lit if gate is not closed + duration TCY
2 = Lit if courtesy light timer (TCY) not elapsed
3 = Gate open indicator on/off
4 = Gate open indicator proportional flashing
Courtesy light duration
Hold-to-run
0 = disabled
1 = enabled
Cycle threshold for assistance request. On reaching the set
threshold the subsequent cycles will be performed with
quick flashing (only if FPr is active).
(0 = disabled)
Enabled in continuous flashing mode for assistance requests
(function only enabled when gate is closed).
0 = disabled
1 = enabled
Water hammer on opening
0 = disabled
Water hammer on closing
0 = disabled
Interval for maintaining hydraulic motor pressure
0 = disabled
from 1 to 480 enabled as follows: 1 = 1 min. ON and 1 min
OFF, 2 = 1 min. ON and 2 min. OFF, ...
Reset to default values
down for 5 seconds
To modify ADVANCED MENU parameters, proceed as described
for the BASIC MENU
DEFAULT
CONFIGURATION
and hold it down). A countdown should now appear: d80,d79...,d01
don
down to " ". Release the key when finished.
MIN MAX
0 0 100
(steps of 5)
1 0 1
0 0 1
0 0 3
0 0 1
0 0 1
0 0 1
% (steps
30 0 100
20 0 900
1 0 1
0 0 10
0 0 4
s (steps
0 0 900
0 0 1
0 0 100
0 0 1
0 0 100 *100ms
0 0 100 *100ms
0 0 480 minutes
UNIT
x 0.01s
of 1)
s
s
of 10s)
x 1000
cycles