Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
3
Use the
(left) and
3 SURR.
Press the ENTER or
setting.
NOTE:
• When "Small" has been selected for the front speakers, "Large" cannot be selected for the surround
speakers.
4
Use the
(left) and
setting.
4 S.BACK
Press the ENTER or
NOTE:
• When "Small" has been selected for the front speakers, "Large" cannot be selected for the surround back
speakers.
5
Use the
(left) and
5 S.WOOFER
Press the ENTER or
SUBWOOFER MODE setting.
• Parameters
Large...... Select this when using speakers that can fully reproduce low sounds of below 80 Hz.
Small...... Select this when using speakers that cannot reproduce low sounds of below 80 Hz with sufficient
volume. When this setting is selected, low frequencies of below 80 Hz are assigned to the subwoofer.
None...... Select this when no speakers are installed.
Yes/No.... Select "Yes" when a subwoofer is installed, "No" when it's not installed.
NOTE:
Select "Large" or "Small" not according to the physical size of the speaker, but according to the bass reproduction
capacity at 80 Hz. If you cannot determine the best setting, try comparing the sound when set to "Small" and
when set to "Large", at a level that will not damage the speakers.
Caution:
In case the subwoofer is not used, be sure to set "Subwoofer = No", or the bass sound of front channel is divided
to subwoofer channel and not reproduced in some mode.
(right) buttons to select your surround speaker type.
(Initial)
LARGE SMALL
NONE
SMALL
(left) button
(right) button
(down) button to switch to the surround back speaker
(right) buttons to select your surround back speaker
(Initial)
LARGE SMALL
NONE
SMALL
(left) button
(right) button
(down) button to switch to the subwoofer setting.
(right) buttons to select your subwoofer setting.
(Initial)
YES
NO
YES
(right) button
(left) button
(down) button to enter the settings and switch to the
Setting the Subwoofer mode and Crossover Frequency
This screen is not displayed when not using a subwoofer.
• Set the crossover frequency and subwoofer mode according to the speaker system being used.
1
Use the
(left) and
6 SW MODE NORM
Press the ENTER or
Crossover Frequency setting.
2
Use the
(left) and
7 CR.OVER
Press the ENTER or
SPEAKER DISTANCE setting.
NOTES:
— Assignment of low frequency signal range —
• The only signals produced from the subwoofer channel are LFE signals (during playback of Dolby Digital or
DTS signals) and the low frequency signal range of channels set to "SMALL" in the setup menu. The low
frequency signal range of channels set to "LARGE" are produced from those channels.
— Crossover Frequency —
• When "Subwoofer" is set to "Yes" at the "Speaker Configuration Setting", set the frequency (Hz) below
which the bass sound of the various speakers is to be output from the subwoofer (the crossover frequency).
• For speakers aet to "Small", sound with a frequency below the crossover frequency is cut, and the cut bass
sound is output from the subwoofer instead.
NOTE: For ordinary speaker systems, we recommend setting the crossover frequency to 80 Hz. When
using small speakers, however, setting the crossover frequency to high frequency may improve
frequency response for frequencies near the crossover frequency.
— Subwoofer mode —
• The subwoofer mode setting is only valid when "LARGE" is set for the front speakers and "YES" is set for
the subwoofer in the "Speaker Configuration" settings (see page 11).
If "SMALL" is set for the front speakers or "NO" is set for the subwoofer, the subwoofer mode setting does
not affect playback of low frequency signal range.
• When the "+MAIN" playback mode is selected, the low frequency signal range of channels set to "LARGE"
are produced simultaneously from those channels and the subwoofer channel.
In this playback mode, the low frequency range expand more uniformly through the room, but depending on
the size and shape of the room, interference may result in a decrease of the actual volume of the low frequency
range.
• When the "NORM" playback mode is selected, the low frequency signal range of channels set to "LARGE"
are only produced from those channels. In this playback mode there tends to be little interference of the low
frequency range in the room.
• Try playing the music or movie source and select the playback mode providing the stronger low frequency
range sound.
ENGLISH
(right) buttons to select the Subwoofer mode.
(Initial)
+MAIN
NORM
(left) button
(right) button
(down) button to enter the setting and switch to the
(right) buttons to select the Crossover Frequency.
(Initial)
80Hz 100Hz 120Hz
80Hz
(left) button
(right) button
(down) button to enter the setting and switch to the
11
Publicidad
Tabla de contenido
