Shure PSM 1000 Guia Del Usuario página 29

SPECIFICATIONS
PSM1000
RF Carrier Range
Compatible Frequencies
Per band
Tuning Bandwidth
Operating Range
environment dependent
Audio Frequency Response
Signal-To-Noise Ratio
A-Weighted
Total Harmonic Distortion
ref. ±34 kHz deviation @1 kHz
Companding
Spurious Rejection
ref. 12dB SINAD
Frequency Stability
MPX Pilot Tone
Modulation
Operating Temperature
P10R
Tri-Band RF Filtering
Active RF Gain Control
Active RF Sensitivity
at 20 dB SINAD
Image Rejection
Adjacent Channel Rejection
Squelch Threshold
Intermodulation Attenuation
Blocking
Audio Output Power
1kHz @ <1% distortion, peak power,
@32Ω
Minimum Load Impedance
High Boost
Volume Limiter
Net Weight
Dimensions
Battery Life
470–952 MHz
varies by region
39
72–80 MHz
Note: varies by region
90 m (300 ft)
35 Hz–15 kHz +/- 1dB
90 dB (typical)
<0.5% (typical)
Patented Shure Audio Reference Companding
>80 dB (typical)
±2.5 ppm
19 kHz (±0.3 kHz)
FM*, MPX Stereo
*ref. ±34 kHz deviation @1 kHz
-18°C to +57°C
–3 dB at 30.5 MHz from the center frequency of
each band
31 dB
Adjusts RF sensitivity to provide more RF dy-
namic range
2.2 µV
>90 dB
>70 dB
22 dB SINAD (±3 dB)
default setting
>70 dB
>80 dB
100 mW (per output)
9.5 Ω
Selectable: +2 dB, +4 dB @ 10 kHz
Selectable: 3–9
Limits volume adjustment knob. Selected value
analogous to volume knob increment.
196 g(6.6) (with batteries)
99 x 66 x 23 mm (3.9 in. x 2.6 in. x 0.9 in.) H
x W x D
4–6 hours (continuous use) AA batteries
P10T
RF Output Power
selectable: 10, 50, 100 mW (+20 dBm)
RF Output Impedance 50 Ω (typical)
Net Weight
4.5 kg (10)
Dimensions 44 x 483 x 343 mm (1.7 x 19.0 x 13.5 in.),
H x W x D
Power Requirement
Audio Input
Connector Type Combination XLR and 6.35 mm (1/4") TRS
Polarity
Configuration
Electronically balanced
Impedance 70.2 kΩ (actual)
Nominal Input Level
switchable: +4 dBu, –10dBV
Maximum Input Level
Pin Assignments
Phantom Power Protection Up to 60 V DC
Audio Output
Connector Type 6.35 mm (1/4") TRS
Configuration Electronically balanced
Impedance Connected directly to inputs
Input: 100–240 V AC, 50/60 Hz, 0.5
Amax. (5.5, with outlet loaded)
Output: 100–240 V AC, 50/60 Hz, 5
Amax., unswitched
XLR: Non-inverting (pin 2 positive
with respect to pin 3)
6.35 mm Tip positive with respect
(1/4") TRS: to ring
+4 dBu: +29.2 dBu
-10dBV:
+12.2 dBu
XLR: 1=ground, 2=hot, 3=cold
6.35 mm Tip=hot, Ring=cold,
(1/4") TRS:
Sleeve=ground
27