Introduction; Machine Specifications; 230V Electrical Schematic - American Sanders FloorCrafter 8 Manual Del Operador

EN
The FloorCrafter can be used on a variety of surfaces. It is an ideal tool for wood flooring maintenance and restoration work. It is
also suitable for cleaning hard surfaces such as tile or Terrazzo.
Part #
Model FloorCrafter 8
Electrical Requirements
230~, 60Hz / 15.7 A, 3.7 kW
Sound Emission (Lpm)* 93.0 dB(A)
Vibration <.15 in/s
Motor
4 Hp Induction
Contact Wheel Rate 2450 rpm
Abrasive Rate 4500 ft/min
Abrasive Size
29½" x 7⅞"
Fan Flow Rate
Drum Settings
Overload Protection
Magnetic Circuit Breaker
Electric Cable 50', 10-3 SJO LP-20P Plug
Operating Controls
Adjustable Lever/Grip
Leveling Controls Externally Adjustable
Operating Wheels 80 Durometer Clear Urethane
Weight
204 lbs.
Dimensions 35 x 13¾ x 38¾
CAUTION: This machine will operate only on AC frequency and on electrical voltage shown on the motor nameplate. Make
sure you have the correct frequency and voltage before connecting the power cord to an outlet. The machine has
a plug as shown below.
This machine must be connected to an electrically ground circuit in order to pro-
tect the operator from electric shock. This machine has an approved power cord
with three conductors as well as a plug with three terminals. Connect the plug into
a three holed receptacle. For maximum protection against electric shock, use a
circuit that is protected by a ground fault circuit interrupter.
DANGER: Electrocution could occur if the machine is exposed to water or rain. Keep the machine in a dry building.
DANGER: Electrocution could occur if machine is improperly connected to the electrical system. To prevent possible electric
shock, always use a 3 wire electrical system connected to an electrical ground. For maximum protection against
electrical shock, use a circuit that is protected by a ground fault circuit interrupter. Consult your electrical
contractor.
DANGER: Electrocution could occur if the ground pin is tampered with in any way. Do not cut, remove, or break the ground
pin. Do not try to fit a three-terminal plug into a receptacle or connector body other than a three plug receptacle
or connector body. If the outlet does not fit the plug, consult your electrical contractor.
DANGER: Electrocution could occur if the machine is used with a damaged plug or power cord. If the cords or plugs are worn
or damaged in any way, have them replaced by an authorized service person or electrician.
Extension Cords
Use only an approved three-pronged extension cord with two main conductors
and one earthing conductor. This machine is equipped
with a power cord. When greater range is needed follow the table
to determine cable gauge of additional footage. Refer to the
chart to the right for extension cord information
If motor appears to labor or takes a considerable longer time to come up to speed reduce sanding pressure.

Machine Specifications

07104A
FloorCrafter 8, Blk
230~, 60Hz / 15.7 A, 3.7 kW
93.0 dB(A)
<.15 in/s
4 Hp Induction
2450 rpm
4500 ft/min
29½" x 7⅞"
234 CFM 234 CFM
80 lbs., 70lbs., 60 lbs. 80 lbs., 70lbs., 60 lbs.
Magnetic Circuit Breaker
50', 10-3 SJO LP-20P Plug
Adjustable Lever/Grip
Externally Adjustable
80 Durometer Clear Urethane
204 lbs.
35 x 13¾ x 38¾
230V Electrical Connection Instructions

Introduction

07104B
FloorCrafter 8
230~, 60Hz / 15.7 A, 3.7 kW
93.0 dB(A)
<.15 in/s
4 Hp Induction
2450 rpm
4500 ft/min
29½" x 7⅞"
234 CFM
80 lbs., 70lbs., 60 lbs.
Magnetic Circuit Breaker
50', 10-3 SJO LP-20P Plug
Adjustable Lever/Grip
Externally Adjustable
80 Durometer Clear Urethane
204 lbs.
35 x 13¾ x 38¾
7
07202A 56380917
FloorCrafter 8
230~, 50Hz / 16.0 A, 3.0 kW
96.2 dB(A)
2.88 m/s rms
2
3 kW Induction
2042 rpm
3750 ft/min
29½" x 7⅞"
195 CFM
80 lbs., 70lbs., 60 lbs.
Magnetic Circuit Breaker
100', H05VVF3G4.0 AV3-20P Plug
Adjustable Lever/Grip
Externally Adjustable
80 Durometer Clear Urethane
204 lbs.
35 x 13¾ x 38¾