Stereo System Features - Jacuzzi J-400 Manual De Instalacion Y Uso & Mantenimiento

Optional Jacuzzi J-1000 Audio System™ Stereo System Features
5
2
17
6
8
16
12
1. Power On/Off Button
2. Tune/Seek Up/Down Button
3. Volume Up/Down Button
4. Mode Button
5. SEL/EQ Button
6. AS/PS Button
7. MUTE Button
8. BAND/RPT Button
9. ENT/SH/RDM Button
10. USB Docking Station
11. AUX Input Jack
12. iPod Docking Station
13. Disc Eject Button
14. CD Installation Slot
15. Front Panel Release Button
16. Front Panel
17. Function Display
18. Infrared sensors
SOUND SYSTEM OPERATION
Power On and Off
Press power button (1) once to turn on stereo system. Press a
second time to turn off.
Adjusting Volume
Press VOL Up/Down button (3) to increase or decrease volume.
Current volume setting is briefly displayed (0 to 45).
7
3
4
9
1
10
11
13
14
15
Mute
In Radio or AUX mode, press mute button (7) once to mute
audio output ("MUTE" appears on display). To restore audio out-
put, press button (7) a second time, or press volume up or down
button.
In the CDP (discs with MP3/WMA files), USB, NAND (internal
memory) or iPod mode this pushbutton allows the tracks to be
temporarily suspended; press again to restart.
Program Selection
Press MODE button (4) to cycle through available program sour-
ces as follows: Radio --> CDP --> USB --> NAND --> IPOD -
-> AUX --> Radio. If a CD or iPod is unavailable, that source will
not appear on the display (17).
Adjusting Bass Level
Press EQ button (5) repeatedly until display reads "BASS". Press
VOL Up/Down button (3) to choose desired setting. A display
of "BASS 0" indicates center, -1 to -7 indicates bass cut, and +1
to +7 indicates bass boost.
Note: Unit returns to volume mode if volume control is not ope-
rated for 3 seconds.
Adjusting Treble Level
Press EQ button (5) repeatedly until display reads "TREBLE. "
Press VOL Up/Down button (3) to choose desired setting. A
display of "TREBLE 0" indicates center, -1 to -7 indicates tre-
ble cut, +1 to +7 indicates treble boost.
Note: Unit returns to volume mode if volume control is not ope-
rated for 3 seconds.
Adjusting Balance Level
Press EQ button (5) repeatedly until display reads "BALANCE. "
Press VOL Up/Down button (3) to choose desired setting. A
display of "BALANCE R-L" indicates center, L01 to 15 indica-
tes left balance, R01 to 15 indicates right balance.
Note: Unit returns to volume mode if volume control is not ope-
rated for 3 seconds.
Adjusting Fader Level
Press EQ button (5) repeatedly until display reads "FADER."
Press VOL Up/Down button (3) to choose desired setting. A
display of "FADER F-R" indicates center, R01 to 15 indicates rear
fade, F01 to 15 indicates front fade.
Note: Unit returns to volume mode if volume control is not ope-
rated for 3 seconds.
Adjusting Beep Level
Press and hold down EQ button (5) for about 2 seconds until
display reads "BEEP 2ND", then release. Press VOL Up/Down
button (3) to select either Beep 2ND (you will hear a "beep"
every time a key is pressed for a few seconds) or Beep On (you
will hear a "beep" each time a key is pressed).
Note: Unit returns to volume mode if volume control is not ope-
rated for 3 seconds.
78