CalSpas Fitness 2400 Manual Del Usuario página 16

Operating Your Spa
turns on automatically, it cannot be deactivated from the
panel; however, the high speed may be started.
Option (Optional Blower)
Press the OPTION button to turn the optional equipment
on and off. If left on, the equipment will automatically
turn off after 15 minutes.
Light
Press the LIGHT button to turn the spa light on and off.
Invert
Press the INVERT button to change the numbers in the
display to read upside down. Another press returns the
display to the right-side-up position. This enables you to
read the display while you are in the spa.
Locking the Panel
To lock the panel:
Press TIME, JETS 1, and the UP button within three
seconds. When locked, the panel will display "LOCK".
All buttons are frozen except the TIME button.
To unlock the panel:
Press TIME, JETS ,1 then the DOWN button within three
seconds.
Setting the Temperature Lock
To activate the temperature lock:
Press the UP or DOWN button, TIME, JETS 1, then the
UP button within three seconds. The panel will display
"TEMP LOCK" when the set temperature is locked.
To unlock the set temperature:
Press the UP or DOWN button, TIME, JETS 1, then the
DOWN button..
Circulation Pump (optional)
If your system is equipped with a circulation pump, it
may be configured to work in one of two different ways:
1. The circulation pump operates continuously (24
hours) with the exception of turning off for 30 minutes
at a time when the water temperature reaches 1.7˚C
above the set temperature (most likely to happen in
very hot climates).
2. The circulation pump will come on when the system
is checking temperature, during filter cycles, during
freeze conditions, or when another pump is on.
Page 16
Preset Filter Cycles
There are two filter cycles per day. The start and end
times of each cycle are programmable. To program, set
the time as instructed above, then press MODE/PROG
to advance to the next setting (or to exit after the last
setting). The default filter cycles are as follows:
• The first filter cycle is automatically activated at 8:00
AM and operates the pump until 10:00 AM. The
"FILTER 1" indicator icon will light when filter 1 is
running.
• The second filter cycle is automatically activated at
8:00 PM and operates the pump until 10:00 PM. The
"FILTER 2" indicator icon will light when filter 2 is
running.
The pump and the ozone generator will run during
filtration. At the start of each filter cycle, the blower will
run on highest speed for 30 seconds to clean out the
air channels. The lowest speed of pump 2 and pump
3 will run for five minutes. In the event of power loss or
shut down, the time of day will need to be reset for filter
cycles to run according to your desired programming.
Clean-up Cycle
When the pump or blower is turned on by a button press,
a clean-up cycle begins 30 minutes after the pump or
blower is turned off or times out. The pump and the
ozone generator will run for one hour.
Ozone (optional)
On most systems, the ozone generator (if installed) runs
during filter cycles (except when pump 1 is operating
at high speed on a non-circulation system) and during
clean-up cycles. On some systems, the ozone generator
operates whenever the pump runs. If your system is
configured with the optional ozone disable feature,
the ozone generator will turn off for one hour any time
a function button (JETS 1, JETS 2, OPTION etc.) is
pressed.
Freeze Protection
If the temperature sensors detect a drop to 6.7˚C within
the heater, the pump automatically activates to provide
freeze protection. The equipment stays on until four
minutes after the sensors detect that the spa temperature
has risen to 7.2˚C or higher. In colder climates, an optional
additional freeze sensor may be added to protect against
freeze conditions that may not be sensed by the standard
sensors. Auxiliary freeze sensor protection acts similarly
except with the temperature thresholds determined by
the switch and without a four minute delay in turnoff.
2009 Portable Spa Owner's Manual
LTR20091001, Rev. A