Parts Removal And Replacement; Feed Tube Removal And Replacement; Screw Gun Removal And Replacement; Drive Shaft, Hex Pin Insert And Bit(S) - OMG AccuTrac Manual Del Propietário

Feed Tube Removal and Replacement

1. Disconnect the upper link from the feed tube assembly by
sliding the black plastic bushings inward and push the
upper link forward to disengage. Repeat the process for
the opposite upper link.
2. The tool can now be removed from the base by pulling up
on the tool.
3. Once the tool is separated from the base, you can remove
the feed tube from the upper tube by pulling on the spring-
loaded retention pin and separating it from the bracket on
the upper tube. The feed tube should now release from the
tool.
4. To re-install the feed tube, align the lower end so that the
"ears" engage the notches of the lower tube.
5. Angle the feed tube towards the upper tube and re-install
the retention pin into the bracket.
6. Re-attach the upper links by sliding the black plastic bush-
ings inward and connecting the links.
W A R N I N G
The nosepiece is not to be removed!
1. The nosepiece is under spring-loaded pressure. Attempting
to remove the nosepiece could cause personal injury.
2. See warning sticker on tool!
3. Contact 1 . 800 . 633 . 3800 to locate your nearest authorized
OMG Roofing Products AccuTrac Distributor and Service
Center.

Screw Gun Removal and Replacement

1. Loosen the star knob assembly on the screw gun motor
clamp and rotate the screw gun in the counterclockwise
direction until the threads disengage.
2. The screw gun must be raised straight up to allow the
screw gun and the attached drive shaft to be removed
from the tool.
3. When the assembly is free, pull the drive shaft from the
screw gun. To re-attach the screw gun, reverse the above
process. Be careful not to over-tighten the screw gun as
this may cause the nosepiece of the screw gun to fall off.

Parts Removal and Replacement

Always Use OMG Roofing Products Replacement Parts
OMG ROOFING PRODUCTS

Drive Shaft, Hex Pin Insert and Bit(s)

1. Remove the screw gun and drive shaft assembly as
described above. Separate the screw gun from the drive
shaft by simply pulling on the shaft from the screw gun.
2. Carefully inspect the drive shaft, spring pin hex insert,
Phillips cap and bit assemblies for excessive wear, cracks
and/or damage of any kind. If either the shaft, spring pin
hex insert, Phillips cap or bits require replacing, use
assembly part number 6634910 (Universal drive shaft),
6606910 (spring pin hex insert), 6722910 (1.4" length
reversible hex bit), 6637910 (Phillips cap) and 6624910
(Phillips bit insert).
3. If only the drive bit
needs to be replaced,
first locate where the
spring pin insert holds
the Phillips cap or hex
bit, then press in on
the spring pin to
affect release.
4. When replacing a
Phillips bit, insert a new
bit into the Phillips cap
then fit it over the end
of the drive shaft, press in on the spring pin while aligning
the hole in the cap or bit and push in until the spring pin
snaps into place.
5. To re-install the hex drive, simply fit it over the end of the
drive shaft, press in on the spring pin while aligning the hole
in the hex drive and push in until the spring snaps into place.
6. Re-install the drive shaft assembly into the screw gun
making sure it snaps into place.
7. Lower the drive shaft/screw gun assembly into the AccuTrac
tool and rotate the screw gun clockwise until tight.
8. Rotate the screw gun to properly align for operation. When
set, securely tighten the star knob on the motor clamp
assembly. Do not over-tighten the screw gun.
800 . 633 . 3800
WWW.OLYFAST.COM
5