Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
INCORRECT INSTALLATION OF THE MACHINE
MAY CAUSE DAMAGE TO PEOPLE, ANIMALS OR
OBJECTS. THE MANUFACTURER CANNOT BE
CONSIDERED RESPONSIBLE FOR THESE DAMA-
GES.
7.1 TRANSPORT AND DISCHARGE
The equipment Aquaplastic is delivered packa-
ged. It must be transported and stored according
to the indications on the packaging.
Due to the low weight of the equipment Aqua-
plastic can be moved by two people without
using other means.
7.2 ARRANGEMENT OF THE LIGHTING SYSTEM
The Client must make sure that there is suitable
lighting for the surroundings and that the lighting
conforms to the regulations in force. In particular,
the Client must arrange the positioning of lighting
that illuminates all the working area.
7.3 ARRANGEMENT OF THE PNEUMATIC SYSTEM
The Client must arrange a line of filtered com-
pressed air supplied by a compressor that is
suitable for the consumption required. Do not use
compressed air that contains chemical products,
synthetic oil with organic solvents, salts or corro-
sive gases as they can cause damage or malfunc-
tioning. The line of compressed air must arrive up
to the supply points of the machine. If the com-
pressed air contains a large amount of moisture,
it may cause malfunctioning in the valves and in
the pneumatic components. Install a moisture
separator downstream from the compressor to
avoid this.
7.4 CLASSIFICATION ACCORDING TO THE ATEX
DIRECTIVE
The machine conforms to the essential requisites
of the EU Directive 94/9/EC, better known as
ATEX ("Explosive atmospheres"). It is classified as
group II category 3 letter G system. The assess-
ment procedures of conformity, carried out by an
internal factory check, allow the installation of
the machine in surroundings where there may be
potentially explosive atmospheres due to the
presence of gas, fumes or mist.
II 3 GD
7. INSTALATION
7.5 POSITIONING
The Aquaplastic must be positioned in a well-ai-
red place.
The area must be equipped with all means provi-
ded for by the Italian Legislative 626/94,
relating to Italian Legislation with reference to the
health and safety of the workers in the working
environment.
Position the machine on the floor and make sure
that there is sufficient space around the machine
to carry out normal maintenance operations or
inspections.
7.6 PUTTING INTO USE
The operations for connecting the machine to the
pneumatic mains supply and positioning the
pipes in the various drums are described below.
1. Connect the earthing cable (No20) provided
with the machine and marked yellow/Green on
the cable lug to a screw on the machine Hood
(No19), on the side of the free terminal to the
earth contact of electric system.
2. Make sure that the two ON/OFF machine and
ON/OFF Brush switches (No17) are in the OFF
position (horizontal). Also check that the mixer
regulator knob is off (rotated fully anti-clockwise).
3. Connect the machine air connection (No03) to
the line of compressed air (max.10 bar).
4. Open the lower door of the machine.
5. Remove the filtrate tank (No5/No10) and the
lower collection tank (No9) of the hollow base of
the washer.
6. Fill the collection basin (No9) with water,
leaving an air space of approximately 5cm
between the water level and the bottom of the
filter basin, which is situated above.
7. Insert the aspirator tuve (No11) supplied with
the suction filter in the lower reservoir or collec-
tion tank.
8. Make sure that the filter tank is positioned
firmly above the supports. Make sure that these
supports are firmly attached media collection
tank and provide stability to the filtrate tank,
which is above.
9. Check that the fabric filter support grid is
correctly positioned inside the filter tank. The
fabric filter must be fixed with the appropriate
filter-holding clips and positioned in such a way
that it adheres to the fabric filter support grid as
well as to the filter tank.
- 16 -
Publicidad
Tabla de contenido
