Weber Spirit E-210 Guia Del Propietario página 10

10
• Do not use a damaged LP cylinder. Dented or rusty LP cylinders or LP cylinders
with a damaged valve may be hazardous and should be replaced with a new one
immediately.
Liquid Propane (LP) Cylinder(s)
• The joint where the hose connects to the LP cylinder must be leak tested each
time the LP cylinder is reconnected. For example, test each time the LP cylinder is
refilled.
• Be sure the regulator is mounted with the small vent hole pointed downward so that
it will not collect water. This vent should be free of dirt, grease, bugs etc.
• The gas connections supplied with your Weber
and tested to meet 100% CSA and ANSI requirements.
WARNING: Replacement LP tanks must match the regulator
connection supplied with this barbecue.
Liquid Propane Cylinder requirements
• Check to be sure cylinders have a D.O.T. certification (1), and date tested (2) is
within five years. Your LP gas supplier can do this for you.
• All LP tank supply systems must include a collar to protect the cylinder valve.
• The LP cylinder must be a 20-lb. size approximately (18¼ inches high, 12¼ inches
in diameter).
• The cylinder should be constructed and marked in accordance with the
Specifications for LP - Gas Cylinders of the U.S. Department of Transportation
(D.O.T.) or the National Standard of Canada, CAN/CSA-B339, Cylinders, Spheres
and Tubes or Transportation of Dangerous Goods; and Commission, as applicable.
LIGHTING
Summary lighting instructions are on the control panel.
Failure to open the lid while igniting the barbecue's burners,
or not waiting 5 minutes to allow the gas to clear if the
barbecue does not light, may result in an explosive flame-up
which can cause serious bodily injury or death.
1) Open the lid.
2) Make sure all burner control knobs are turned to OFF. (Push control knob down and
turn clockwise to ensure that it is in the OFF position.)
WARNING: The burner control knobs must be in the OFF
position before turning on the liquid propane cylinder tank
valve. If they are not in the OFF position, when you turn on
the LP cylinder valve, the "excess gas flow control" feature
will activate, limiting the flow of gas from the LP cylinder. If
this should occur, turn off the LP cylinder valve and burner
control knobs. Then start over.
When the "excess gas flow control" feature is activated,
a small amount of gas is still flowing to the burners. After
turning OFF the cylinder valve, wait at least 5 minutes for the
gas to clear before attempting to light the barbecue. Failure
to do so may result in an explosive flame-up, which can
cause serious bodily injury or death.
GAS INSTRUCTIONS
®
gas barbecue have been designed
OPERATING INSTRUCTIONS
DANGER
DANGER
In Canada
Liquid Propane Cylinder requirements
Note: Your retailer can help you match a replacement tank to your barbecue.
• The LP cylinder must be constructed and marked in accordance with the
specifications for LP gas cylinders, T.C.
Crossover ® Ignition System
®
Note: The Crossover ignition system ignites the Front burner with a spark from the
igniter electrode inside the Gas Catcher™ ignition chamber. You generate the energy
for the spark by pushing the Crossover
WARNING: Check hose before each use of barbecue for nicks,
cracking, abrasions or cuts. If the hose is found to be damaged
in any way, do not use the barbecue. Replace using only Weber
authorized replacement hose. Contact the Customer Service
Representative in your area using the contact information on
our web site. Log onto www.weber.com
MAIN BURNER LIGHTING
SPIRIT
E/SP-210 & 310
*The grill illustrated may have slight
differences than the model purchased.
1
DOT 4BA240
00/07
2
® ignition button until it clicks.
®
.
1
2
6
4
WWW.WEBER.COM
®
7
5
3
®