Extension Table - Festool CS 70 VL Instrucciones De Montaje

Compact CS 70 / TKS 80 EBS Accessories
1 Symbols
Warning of general danger
Read the operating instructions and
safety instructions.
Do not dispose of it with domestic
waste.
L For the alignment and adjustment of all individ-
ual components, we recommend using a spirit
level or an aluminium ruler (min. 1 m long).
2 Removable leg TKS 80 EBS [1-1]
WARNING
Risk of accident from tilting power tool
fAlways use the removable leg in conjunction
with the TKS 80 VB width extension table and
the TKS 80 VL length extension table.
fMake sure that the removable leg and the
foldaway legs of the TKS 80 EBS are stable.
Proceed as follows (fig. 1):
fLoosen the rotary knob screws [1-2].
fPlace the removable leg [1-1] on the rotary
knob screws [1-2].
fTighten the rotary knob screws [1-2].
3

Extension table

CS 70 VB / TKS 80 VB [2-3]
The extension table CS 70 VB / TKS 80 VB can be
fitted to the base table to enable exact cuts with a
stop up to a cutting width of 680 mm (CS 70 VB) /
600 mm (TKS 80 VB).
The saw table is widened by 405 mm if an extension
table is fitted on a long side of the table (usually
the right).
Proceed as follows (fig. 3):
fUnfold supports [3-7] at a 90° angle to the ta-
ble top.
fTurn rotary knobs [3-4] fully to the left.
fPlace the outer edge of the extension table on
the edge of the base table in a slightly raised
position (fig. 3).
fLower extension table so that the peripheral
clamping edge [3-1] lies between the profile
edge [3-5] and clamping plate [3-3].
fInsert the end of the front support [3-9] into
the slot [3-1] in the table frame, push down
and tighten with knurled nut [3-8].
fSuspend rear support in slot. Push extension
table down and tighten rear knurled nut.
fAdjust exact height. Place guide stop on base
table up to saw blade.
fAdjust height of extension table to same height
as base table with screwdriver at the adjusting
screws [4-2].
fAttention! Do not align with outer edge of ta-
ble since this may be 0.2-0.3 mm below the
rest of the table.
fFit angle fence [2-1] centrally over joint be-
tween base table and extension table so that
when the fence is clamped the extension table
is aligned with the edge of the base table.
fTighten front rotary knob [3-4].
fPush extension table down on joint at rear and
tighten rear rotary knob.
fThen remove the angle fence [2-1].
fScrew in adjusting screws [3-2] fully with
screw-driver.
fIf the extension table is removed and then re-
mounted it must be pushed back against this
stop (adjusting screw). This fixation means
that it no longer has to be aligned with the an-
gle fence.
fCheck that the extension table is exactly level
with the base table using the guide stop.
fThe flatness of the base table can be adjusted
by adjusting the fastening [3-6].
To enable the angle fence and ripping-cut fence
to be adjusted according to the existing scale, the
scale of the extension table must be fitted directly
onto the base table's scale (fig. 4).
Proceed as follows:
fRelease the fastening bolts [4-1] for the ex-
tension table's scale.
fSlide the scale to the correct setting.
fRe-tighten fastening bolts.
9
English