Cardin Elettronica S48 AM Manual De Instrucciones página 2

Ocultar thumbs

página de 6

/ 6
Marcadores

Idiomas disponibles

CARDIN

Via Raffaello, 36- 31020 San Vendemiano (TV) Italy

Tel:

Fax:

email (Italy):

email (Europe):

Http:

Attention! Only for EU customers - WEEE marking.

This symbol indicates that once the products life-span has expired it must be disposed

of separately from other rubbish. The user is therefore obliged to either take the product

to a suitable differential collection site for electronic and electrical goods or to send it

back to the manufacturer if the intention is to replace it with a new equivalent version

of the same product.

Suitable differential collection, environmental friendly treatment and disposal contributes to avoiding

negative effects on the ambient and consequently health as well as favouring the recycling of materials.

Illicitly disposing of this product by the owner is punishable by law and will be dealt with according to the

laws and standards of the individual member nation.

Description

The S48 Radio control system consists of one or more transmitters and one or more receivers which can be

combined to meet the specific needs of the system. This encoding system has 7.000.000 possible combinations,

and allows a different code (for different receivers) to be programmed for each available button.

use

The S48 radio control allows the remote activation of electrical and electronic appliances with its best use

in the following areas: automatic opening systems, alarm systems, and in all systems which require remote

control activation (without wires) using secret codes, in compliance with the safety standards governing the

installation of appliances.

Transmitter versions

TRQ048200

miniaturized transmitters

TRQ048400

miniaturized transmitters

Receiver versions

RCQ048100

receiver + container

RCQ0481MM

with channel memory

RSQ048200

slot-in receiver cards

RQM048200

mini receiver + container

Receiver antenna installation

Minimum and maximum range of the radio controls. 'Range' is intended to mean the working distance, meas-

ured in free space, between the receiver and the transmitter with the antenna installed. The range is therefore

closely linked to the technical characteristics of the system (power and sensibility) and varies according to

the characteristics of the site in which the system is located. It therefore follows that to obtain the best results

from the radio control the installation sites for the receiver and the antenna should be carefully chosen. It is not

possible to install 2 receivers at a distance of less than 1.5 m from each other. It is good practise to position the

receiver away from computer systems, alarm systems and other possible sources of disturbance.

(A bad choice of positioning could compromise the performance of the receiver).

Antenna

The installation of the antenna is fundamental, connected to the receiver it represents the reception point for

the radio control. When installing the antenna the following points should be observed:

- Only use a tuned antenna connected to the receiver using a coaxial cable RG58 (impedance 50Ω) with a

maximum length of 15 m;

- The antenna should be positioned out of doors in the highest possible point, visible and away from metal

structures.

Note: If for some particular reason it is not possible to fit an antenna, a reasonable performance can be obtained

by connecting a 2,5 m piece of single pole conductor wire (Ø1 mm) to the receiver.

Receivers

Warning! The receivers must only be powered by a safety power pack. The use of non safety power packs

could provoke damage to the system.

Outdoor receivers IP55 (fig. 1)

The receiver is in an outdoor case fitted with a 14-way terminal board (p.c.b CS1268B-fig. 1) with the follow-

ing electrical connections:

- 12V ac/dc between binding posts 11-12 - 24V ac/dc between binding posts 10-12

The case type receiver is fitted using "fast-fitting" brackets. The bracket should be fixed to the wall using two raw

plugs (check that it is in square). After connecting the wiring the case should be slid onto the bracket therefore

fixing it to the wall. If any repair work is necessary the case can be easily extracted by pushing upwards the

action of which will separate it from the bracket.

Interchangeable channel modules

In the receivers (with container) the interchangeable channel modules can only have the following configura-

tions and must not be mixed:

- from 1 to 4 impulsive relay strips MCC4491R0

- one memory relay strip MCC0381M0 (On/Off)

- one timer relay strip MCC0381T0

Slot-in receiver card (fig. 2)

Warning! The receiver cards must be sufficiently insulated from the parts of the host device which are powered

by the mains.

- The receiver card (printed circuit CS1300) is inserted directly into an appliance which is designed to receive

and has the following electrical connections:

- 12V ac/dc with jumper "J1" in position "B" - 24V ac/dc with jumper "J1" in position "A"

The receiver cards are fitted with two relays, the outputs of which are marked CH1 (normally open contact)

and CH2 (normally open/normally closed contact). The relays CH1 and CH2 can be activated by selecting the

functions A-B-C-D and made to correspond with the transmitter channels CHA-CHB-CHC-CHD by setting the

jumpers situated on the circuit board (see fig. 2).

Mini receivers IP43 (fig. 3)

- The mini receiver (printed circuit CS1299) is housed in an indoor container, it is fitted with an 8-way terminal

board and has the following electrical connections:

24V ac/dc between binding posts 5-6.

The mini receivers are fitted with two relays, the outputs of which are marked CH1 and CH2 (normally open

contacts). The relays CH1 and CH2 can be activated by selecting the functions A-B-C-D and made to cor-

respond with the transmitter channels CHA-CHB-CHC-CHD by setting the jumpers situated on the circuit

board (see fig. 3).

ELETTRONICA

+39/0438.404011-401818

+39/0438.401831

Sales.office.it@cardin.it

Sales.office@cardin.it

www.cardin.it

RANDOM CODE QuARTZ RADIO CONTROLS S48

2 buttons

4 buttons

4 channels

2 channels

1 channel

1 channel ON-OFF

1 channel 0,5 to 120 s

spa

SERIAL NUMBER

ZVL118.08

The S48 series conforms to the essential requirements of the directive

99/05/CE and the technical reference standards have been applied. This

product has been tried and tested in the manufacturer's laboratory, during

the installation of the product follow the supplied indications carefully.

Transmitters

The transmitter channels are already fixed with each key corresponding to a specific channel. In the two

channel transmitters it is possible to select channel "A" for both of the keys (by means of a jumper on the

receiver "S1 in position CH-A fig. 1"). In this case the channel module need only be inserted in slot "A".

Nota: Transmitters of the series with display "8, 16 and 100 channels can be used

with standard "Mini, Slot-in and outdoor receivers. Cutting the resistor "R0" will

allow you to memorise them in blocks of four channels.

Channel receiver

Channel transmitter

GENERATING THE S48 RADIO RECEIVER uSER CODE

Starting up - Generating the code (fig. 1-2-3)

1) Switch on the power supply to the receiver

2) Move dip 1 of the dip-switch "D1" to the "ON" position (starts generating random codes), after

a few seconds move it back to the "OFF" position.

3) Move dip 2 of the dip-switch "D1" to the "ON" position (from this point the secret code is

already memorised in the receiver). Move dip 2 to the "OFF" position.

MEMORIZING THE S48 RADIO CONTROL uSER CODE

Attention: If you are carrying out a new installation you must first generate the user code in the receiver as

described in the previous paragraph.

1) Insert the transmitter into the interface on the receiver (fig. 1,2,3,6).

2) Press the key which corresponds to the channel which has to learn the secret code. Repeat the operation

for as many channels as are required A-B-C-D (fig. 5).

- Each key on the transmitter corresponds to a specific channel.

- Each key can either be associated with the same code for all available channels (if they are all inserted from

the same receiver), or with different codes if they are inserted from different receivers.

Note: If the code has been correctly learnt a led will light up on the receiver (fig. 1-2-3 "LD"). To ensure the exact

correspondence when associating one or more receivers with one or more transmitters remember to take into

account the association with the various channels.

Memory module

This is extractable, furnished with a non volatile EEPROM type memory and contains the system code. The pro-

grammed code is maintained in this module even in the absence of power, it is therefore possible to extract the module

for maintenance purposes and reposition it inside another receiver which will automatically use the same code.

Attention! If you remove a memory module from a working receiver it will no longer be able to read the code

after a blackout. In fact when the power is turned back on the receiver won't recognise the transmitters which

were previously programmed into it.

Duplicating a memory module ("M1" fig. 1-2)

Note: Excluding Mini receivers.

1) With the receiver powered up remove the original memory module and insert the new one.

2) Move dip 2 of the dip-switch "D1" from the "OFF" position to the "ON" position then reposition it in "OFF"

at this point the new module has been encoded with the same code as the original. Switch the power to the

receiver "OFF" and "ON" to ensure the code has been memorised and then try and activate a function on

the transmitter.

Channel functions for the S48 radio controls (fig. 5)

Channel "A" of the transmitter must always correspond to channel "A" of the receiver and so forth for all four

of the available channels. Remember that the receiver can only respond to one signal at a time, it therefore

follows that several channels cannot be activated simultaneously.

RCQ0481MM receiver with On-OFF functions, activated by means of a 4 way dip switch ("D2" fig. 1):

Position OFF: impulsive channels

Position ON:

ON-OFF channels

Note: The dip switches must be set before switching on the power supply to the receiver

TECHNICAL SPECIFICATIONS

The transmission frequency of these products varies according to the approved frequency and

eventual personalisation in the country of destination

Country

Only Italy

Europe / USA

RECEIVER

- antenna impedance in input ....................................................................................................................... 50Ω

- sensibility (fine signal)...............................................................................................................................0.5 µV

- local oscillation emission ...................................................................................................<-70dBm (<100pW)

- power supply ...............................................................................................................................12-24V ac/dc

- maximum power consumption at rest/ activated relay .............................................................40 mA / 66 mA

- maximum commutable power at the relay load ac/dc ....................................................................60VA/24W

maximum voltage ..............................................................................................................................30V ac/dc

- excitation delay/dropout delay ..............................................................................................................150 ms

TRANSMITTERS

- apparent radiated power .........................................................................................-10...-7 dBm (100-200 µW)

- apparent power harmonic products ..................................................................................... <-64 dBm (<1 nW)

- power output adjacent channel (± 10 kHz) ........................................................................ <-37 dBm (<0.2 µW)

- modulation ............................................................................................................................................ AM/ASK

- signal modulation ......................................................................................................................PCM, 1.3 ms/bit

- power supply ..................................................................................................................................... 12V ± 10%

- maximum power consumption ...............................................................................................................<40 mA

- operating temperature range .......................................................................................................- 20... +70 °C

- relative humidity ..................................................................................................................................... < 95 %

SERIES

MODEL

S48