Publicidad
Idiomas disponibles
Idiomas disponibles
Installation and moving
Your dishwasher has arrived
After having bought or moved your dishwasher to another home, a correct
installation ensures that your dishwasher will operate smoothly and efficiently.
Choose where you want to
install your dishwasher,
you can even place it so that
its sides or back panel are
side by side with furniture
or up against the wall. The
dishwasher is provided with
water supply and drain
hoses, which can be directed
towards the left or right to
facilitate
appropriate
installation.
Levelling.
Once the appliance is
positioned, adjust the feet
by screwing them in or out
depending on how high you
want it and to level it so that
it is horizontal. Make sure
that it is not inclined more
than 2 degrees. If the
appliance is level, it will he
lp ensure its correct
operation.
Adjusting the Back Feet
Insert the appliance into the
cutout and then adjust the
height using the screws
located on the front bottom
part of the machine. Use a
screwdriver to turn the
screws in the clockwise or
anti-clockwise direction to
increase or decrease the
height respectively.
Cold water connection.
Connect the cold water
supply hose to a 3/4 gas
threaded connection, taking
care to screw it tightly onto
the tap. If the water hoses
are new or have been out of
use for an extended period
of time, let the water run to
make sure it is clear and
free of impurities before
making the connection. If
this precaution is not taken,
the water inlet could get
blocked, causing damage to
your dishwasher.
-It is strongly recommended
to use a new hose to connect
the dishwasher to the water
supply line, and the old
hose-set should not be
reused. Asking to specilized
shop or an authorized
service technician (see
Service).
Hot water connection.
Your dishwasher can be
supplied with hot water
from the mains supply (if
you have a central heating
system with radiators) at a
temperature of no more
than 60°C.
In this case, the wash cycle
time will be about 15
minutes shorter and the
wash will be slightly less
effective.
The connection must be
made to hot water supply
following
the
same
procedures
as
those
indicated for the cold water
connection.
Anti-flooding protection
Your dishwasher is provided
with a special system which
blocks the water supply in
the event of leaks inside the
appliance. It is further
equipped with a water inlet
hose that can withstand
extremely high pressures
and that turns bright red in
the event of breakage.
Safety in the event of flood-
ing is ensured by the second
clear hose that contains the
former and thus highlights
the latter when it has
turned bright red. It is vi-
tal that you check it on a
regular basis: if you see it
has turned bright red, then
you know you have to re-
place it as soon as possible.
Call for an authorised tech-
nical engineer to come and
replace it.
Drain hose connection.
Fit the drain pipe into a
drain line with a minimum
diameter of 4 cm or place it
over the sink. Avoid restrict-
ing or bending it. The part
of the pipe marked with the
letter A should be between
40 and 100 cm above the
ground.
The pipe should not be im-
mersed in water.
A
Condensation-proof tape.
On
some
models,
transparent condensation-
proof adhesive tape has been
provided.
It should be stuck onto the
lower side of your wooden
worktop to protect it from
the
formation
condensation.
When not provided, this tape
can be requested as a spare
part from authorised
retailers.
Electrical connection.
First of all, check that the
mains
voltage
and
frequency
values
correspond to those stated
on the rating plate located
on the stainless steel inner
door of the appliance and
that the electrical system to
which the dishwasher is
connected is sized for the
maximum
current
indicated on said rating
plate.
Earth: indispensable
safety.
Only now can you plug the
appliance into a socket
provided with an efficient
earth connection (the
system's earthing is a
guarantee of safety provided
for by law, make sure your
system has it).
ARISTON DISHWASHER - Instructions for installation and use
D
1509)50-4
Attention
a
- Once the appliance has
been installed, the electrical
plug and socket should re-
main accessible.
- If the power supply cable
is damaged, it must be
replaced
by
of
manufacturer
Technical
Assistance
Service in order to prevent
all potential hazards. (See
Assistance)
- The cable should not be
bent or compressed.
- The Company shall not be
held responsible for any
incidents that occur if these
regulations
are
observed.
If the power
socket to which
the appliance is
connected is not
compatible with
the plug, replace
it with a suitable
plug rather than
using adapters or
multiple plugs as
these could cause
overheating or
b u r n s .
the
or
its
not
19
Publicidad
