On Handling Discs; Connections - Denon ADV-700 Manual De Instrucciones

F_ CAUTIONS ON HANDLING DISCS r_ CONNECTIONS
Only the discs including the marks shown on page 4 can be
played on the ADV-700.
Note, however, that discs with special shapes (heart-shaped
discs, hexagonal discs, etc.) cannot be played on the ADV-700.
Do not attempt to play such discs, as they may damage the
player.
• Do not get fingerprints, grease or dirt on discs.
• Be especially careful not to scratch discs when removing
them from their cases.
• Do not bend discs.
• Do not heat discs.
• Do not enlarge the center hole.
• Do not write on the labeled (printed) side with a ball-point
pen or a pencil.
• Water droplets may form on the surface if the disc is moved
suddenly from a cold place to a warm one. Do not use a
hairdryer, etc., to dry the disc.
Avoid touching the surface of discs when loading and unloading •
them. •
B ful net to get fingerprints ..... __
on the signal surface (the side
which shines in rainbow colors).
Always eject discs after playing them.
Keep discs in their cases to protect them from dust,
scratches and warping.
Do not put discs in the following places:
1. Places exposed to direct sunlight for long periods of time
2. Humid or dusty places
3. Places exposed to heat from heaters, etc.
• Fingerprints or dirt on the disc may lower sound and picture
quality or cause breaks in playback. Wipe off fingerprints or
dirt.
• Use a commercially available disc cleaning set or a soft cloth
to wipe off fingerprints or dirt.
Wipe gently from the middle Do not wipe with a circular
outwards, motion.
NOTE:
• Do not use record spray or antistatic. Also do not use
volatile chemicals such as benzene or thinner.
• Only load one disc at a time. Loading one disc on top of
another may result in damage or scratch the discs.
• Load 8 cm discs securely in the disc guide, without using an
adapter. If the disc is not properly loaded, it may slip out of
the guide and block the disc tray.
• Be careful not to let your fingers get caught when the disc
tray is closing.
• Do not place anything but discs in the disc tray.
• Do not load cracked or warped discs or discs that have been
fixed with adhesive, etc.
• Do not use discs on which the adhesive part of cellophane
tape or glue used to attach the label is exposed, or discs
with traces of tape or labels that have been peeled off. Such
discs may get stuck inside the player, resulting in damage.
Record Thinner Benzene
spray
• DO not plug in the AC cord until all connections have been
completed.
• Be sure to connect the left and right channels properly (left
with left, right with right).
• insert the plugs securely, incomplete connections will
result in the generation of noise.
• Note that binding pin plug cords together with AC cords or
placing them near a power transformer will result in
generating hum or other noise.
• Noise or humming may be generated if a connected audio
equipment is used independently without turning the
power of this unit on. If this happens, turn on the power of
the this unit.
• When making connections, also refer to the operating instructions of the other components.
Connecting the DIGITAL (optical) jacks 1
Use these for connections to audio equipment with digital (optical) output.
NOTE:
• Use optical cables for optical connections, removing the cap before connecting.
NOTES:
• Track numbers may not be added automatically when
making digital recordings of CDs being played on the ADV-
700 onto a connected recorder.
• When making digital recordings on a CD recorder, set the
CD recorder's recording setting to manual and add track
numbers (track marks) manually as you record.
• When making digital recordings on an MD recorder, use
the editing function after the recording is completed to
divide the tracks.
Connect the tape deck's recording input iacks (LINE IN or REC) to
this unit's tape recording (CDR/TAPE OUT) jacks using pin plug
cords.
Connections for playback:
Connect the tape deck's playback output jacks (LINE OUT or PB)
to this unit's tape playback (CDR/TAPE IN} iacks using pin plug
cords.
5