Front Panel - Fender Super Bassman Instrucciones De Funcionamiento

Thank you for choosing the Fender® Super Bassman 300
watt tube bass head. This amplifier was designed to
provide the ultimate bass playing experience, with two
channels (Vintage/Overdrive), classic good looks and
modern technology designed to maximize classic tech-
nology.
The Vintage channel offers a classic Fender passive tone
stack. This "cut-only" interactive circuit provides a dis-
tinctly old-school caramel-like thickness to the notes.
The Overdrive channel has an active tone stack, very
quick and responsive, with the ability to get incredibly
1 2
PULL DEEP
VOLUME BASS
INPUTS
A. INPUTS:
Plug your bass into the input that sounds
the best to you. Input 2 is a lower sensitivity input (–6dB)
and provides cleaner response with high-output or active
instruments. If both inputs are used simultaneously, their input
sensitivities become identical, both –6dB.
B. VOLUME: Adjusts the volume level of the Vintage channel.
C. BASS/MID/TREBLE: Classic, cut-only (passive) tone stack. Pull
the BASS knob out for emphasis in the low-frequency range
(DEEP). Pull the TREBLE knob out for an increase in the high-
frequency range (BRIGHT).
D. CHANNEL SELECT: Selects the active channel as indicated
by the green and red LEDs. When the VINTAGE channel is
selected (switch in the down position, green LED), the knobs
on the left (B–C) are active. When the OVERDRIVE channel is
selected (switch in the up position, red LED), the knobs on the
right (E–J) are active.
♫
The included Footswitch can also be used to select channels.
See FOOTSWITCH (U) on next page.
E. GAIN: Adjusts the amount of preamp tube distortion in the
Overdrive channel.
F. BLEND: Controls the amount of distorted signal (set by GAIN)
to be blended with the clean bass signal. Lower settings can
maintain a cleaner tone, with some added grit. Higher settings
will produce more distorted tones and add sustain. Set to "1"
for clean tube bass signal only.
NOTE: The TUNER OUT (V), POWER AMP IN and PRE AMP OUT (W) jacks are balanced TRS (Tip/Ring/Sleeve)
type jacks, with tip=positive (+), ring=negative (–) and sleeve=ground (GND). While standard shielded TS (Tip/
Sleeve) "mono" guitar cables can certainly be used, the use of "stereo" TRS cables may improve signal-to-noise
ratio and reduce hum due to line noise.
Super Bassman®

Front Panel

OVERDRIVE
VINTAGE
PULL BRIGHT
MID TREBLE GAIN BLEND
TRS Connections
aggressive. Foot switch between these on stage for an
instant tone make-over.
Fender Automatic Bias removes "tube anxiety" by con-
stantly monitoring and re-biasing the tubes for perfect
performance and alerting when service is required.
Silent recording is easy. Simply turn the Speaker Output
switch to MUTE and capture the preamp tone out of the
XLR output without waking the neighbors!
The Super Bassman will provide a life time of thick, natu-
ral, balanced tone that sits fat in your live or studio mix.
PULL DEEP
VOLUME BASS FREQ MID LEVEL
G. VOLUME: Adjusts the volume level of the Overdrive channel.
Use together with the GAIN knob (E) to set the overall
loudness of the Overdrive channel.
H. BASS: Adjusts the amount of low-frequency boost or cut
(±15dB) of the Overdrive channel. Set this knob to the center
detent position for flat bass response. Pull this knob out for
low-frequency emphasis (DEEP).
I. MID FREQ/MID LEVEL: Use the FREQ knob to set the
frequency at which the LEVEL knob adjusts the middle-
frequency boost or cut (±18dB) of the Overdrive channel. Set
the LEVEL knob to the center detent position for flat mid
response.
♫
It is easiest to adjust MID when the LEVEL control is at its
maximum or minimum, so that the effect of the FREQ knob
is more easily heard. Once the proper FREQ setting is found,
adjust the LEVEL knob to the desired setting.
J. TREBLE: Adjusts the amount of high-frequency boost or cut
(±15dB) of the Overdrive channel. Set this knob to the center
detent position for flat treble response. Pull this knob out for a
high-frequency boost (BRIGHT).
K. MASTER: Adjusts the overall volume of the amplifier. Pull this
knob out to mute all outputs from the amp except the TUNER
output, useful for silent instrument tuning.
L. POWER INDICATOR: Illuminates when power to the unit is
switched on.
1
PULL BRIGHT PULL MUTE
TREBLE MASTER