System Inspection And Maintenance - 3M Speedglas 9100 FX Manual De Instrucciones

3M™ Speedglas™ Complete Helmet Assemblies
06-0600-10SW Welding Helmet 9100 FX SideWindows with ADF 9100V
06-0600-20SW Welding Helmet 9100 FX SideWindows with ADF 9100X
06-0600-30SW Welding Helmet 9100 FX SideWindows with ADF 9100XX
3M™ Speedglas™ Replacement Parts and Accessories
04-0320-00 Batteries (CR-2032)
06-0000-10 ADF 9100V
06-0000-20 ADF 9100X
06-0000-30 ADF 9100XX
06-0200-10 Inside Protection Plate 9100V (5 pack)
06-0200-20 Inside Protection Plate 9100X (5 pack)
06-0200-30 Inside Protection Plate 9100XX (5 pack)
06-0201-10 Starter Kit 9100V (5 Outside & 2 Inside Protection Plates, 1 sweatband)
06-0201-20 Starter Kit 9100X (5 Outside & 2 Inside Protection Plates, 1 sweatband)
06-0201-30 Starter Kit 9100XX (5 Outside & 2 Inside Protection Plates, 1 sweatband)
06-0200-51 Outside Protection Plate 9100, Standard
06-0200-52 Outside Protection Plate 9100, Scratch Resistant
06-0200-53 Outside Protection Plate 9100, High Temperature
06-0200-54 Sweatband 9100
06-0400-51 Headband Assembly 9100 Complete (headgear)
06-0400-52 Pivot Mechanism 9100 (Left & Right)
06-0400-53 Headband 9100 Front Part
06-0400-54 Headband 9100 Back Part (ratchet adjuster)
06-0400-55 Battery Holder 9100
06-0500-51 Head Protector 9100, Tecaweld
06-0500-52 Ear and Neck Protector 9100, Tecaweld
06-0500-54 Welding Beanie Hat, (no visor)
06-0500-55 Welding Cap with Visor
06-0500-56 Magnifi cation Plate 1.5X
06-0500-57 Magnifi cation Plate 2.0X
06-0500-58 Magnifi cation Plate 2.5X
06-0500-59 Magnifi cation Plate 3.0X
06-0500-60 Cloth Storage Bag
06-0500-61 Branded Toolbox Decal
15
06-0700-51 Wideview Clear Grinding Visor, Standard
06-0700-54 Wideview Clear Grinding Visor, Anti-Fog
06-0700-63 Chrome Front Panel, 9100 FX
06-0700-64 Wideview Clear Grinding Visor Frame, 9100 FX
06-0700-73 SideWindow Covers, 9100 FX
06-0700-81 Standard Headcover, 9100 FX
06-0700-82 Extended Headcover (Head and Neck), 9100 FX
06-0700-83 Full Hood, Black

SYSTEM INSPECTION AND MAINTENANCE

Never modify or alter this welding helmet. Repair or replace parts only with approved 3M components.
Utilizing components other than those supplied by 3M may adversely affect the performance of the welding
helmet and may result in serious injury or death.
This headgear must not be painted or cleaned with solvents. Any decals applied to the headgear must be
compatible with the surface material and known not to affect adversely the characteristics of the materials
used in the headgear. Decals may affect the fl ammability characteristics of this headgear.
Carefully inspect the complete 3M™ Speedglas™ Welding Filter, 9100 before each use. Cracked, pitted or
scratched fi lter glass or protection plates reduce vision and can seriously impair protection. All damaged
components should be replaced immediately. Remove any protective fi lm from the visor.
Any headgear subjected to severe impact should be replaced.
Inspect the welding helmet and headgear for any worn or damaged parts. Replace any worn or damaged
parts utilizing those components listed in the replacement parts and accessories list contained in this User
Instruction.
To check for proper ADF operation, hold the ADF within a few inches of a fl uorescent light bulb and observe
the ADF switch to the selected dark state. Depending on the light source, it may be necessary to temporarily
increase the sensitivity setting. Optionally, the ADF can be triggered by pointing any electronic device remote
control (e.g. television) at the ADF sensors and by pushing the "On" button.
Note: If the ADF does not function as described in these User Instructions, do not use and immediately contact
your supervisor or 3M representative.
WARNING
W
16