Tabla de contenido
Publicidad
7. Filters:
7.1 Median Filter
(1)
(It cannot be changed, if it is
approved. Some models do not
have the function.)
Minimum value is 1, maximum
value is 9. If different value is
entered, all filters run with default
values.
7.2 Average Length
(50)
(It cannot be changed, if it is
approved. Some models do not
have the function.)
Minimum value is 10, maximum
value is 50. If different value is
entered, all filters run with default
values.
7.3 Minimum Average Length
(1)
(It cannot be changed, if it is
approved. Some models do not
have the function.)
Minimum value is 1, maximum
value is 25. If different value is
entered, all filters run with default
values.
7.4 Filter Break Count Value
(It cannot be changed, if it is
approved. Some models do not
have the function.)
Minimum value is 70, maximum
value is 2800. If different value is
entered, all filters run with default
values.
7.5 Automotic filter mode(wind filter)
(Off)
This mode is activated 7.1 and 7.3 filter
settings
becomes
dysfunctional.Device
makes automatically
the filter settings
based on operating conditions.
8. Calibration:
8.1 Calibration coefficient
(It can be changed, if the calibration
key is ON)
8.2 Maximum capacity
(It can be changed, if the calibration
key is ON)
8.3 Divison
(1)
0 : 3000
1 : 2 x 3000
2
:
3
x
3 : 6000 / 7500
4
:
12000
15000(division
not be
set
it
approved)
6 : 1500
(It can be changed, if the calibration
key is ON.)
- 17 -
8.4 Load Cell Maximum Capacity
(It can be changed, if the calibration
key is ON.)
8.5 Maximum capacity unit
(It can not be changed, if it is
approved)
8.6 Gravity value of place where
instruments
3000
(It can be changed, if the calibration
(divis
key is ON)
ion
8.7 Gravity value of place where
can
instrument will be used
not
be
set if
(It can be changed, if the calibration
it
is
key is ON)
appr
oved
8.8 Load Cell mV/V value
)
(divis
ion
9. Relay settings:
can
not
be
10. Interface settings:
set if
(Only for PRINTER/PC type scales.)
it
is
10.1
Communication
appr
oved
)
/
can
it
is
10.2
(1)
0 : g
1 : kg
2 : ton
was
calibrated
10.3
(9.8022)
(9.8006)
10.4
mv/V value of used
Load Cell
It determines data package will be
transmitted to PC.
Not in this type.
transmitted.
X X X X X
transmitted.
ON/OFF
(On)
If it is ON :RS232
communication is
active.
If it is OFF : RS232
communication is
inactive.
(It must be activated
in only for printer/pc
type
scales,
otherwise
ER
8
- 18 -
message
will
be
seen.)
ID Number
(8888)
For PC output this
Number
is
Instrument ID that is
transmitted to PC in
every
package
except
continuous
transmitting is ON.
See details in related
documents.
Continuous
transmitting
(Off)
If it is ON: Activates
continuous
data
transfer from scale to
computer.
If it is OFF :
Communication is
not continuously,
communication is
done when a request
send from computer.
PC data package selection
(11111)
1:
It
will
be
0: It will not be
Price detail (Sum
and Unit Price)
Date and Time
Tare
Mirror enable
Unit detail
NOTE:
If
it
is
approved,
price
detail, unit detail and
Publicidad
Tabla de contenido
