Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
V. Initial setup
1.
Install the two AAA supplied batteries inside the remote control.
2.
Next, connect the front, center and rear satellite speakers to the corresponding output (yellow)
jacks on the back of the main unit.
3.
Connect the left (red) and right (white) RCA plugs into the matching input jacks on the back of
the main unit for wired playback from audio devices fitted with a 3,5mm stereo connection.
Proceed to connect an external audio device, such as a laptop, television set, MP3/4 player,
smartphone or tablet.
4.
In addition, the DVD inputs let users enjoy multichannel surround sound, through the use of the
subwoofer and the five satellites (two front and two rear speakers, plus one center speaker).
Audio RCA cables are required to do the connections, which are not supplied. When connec-
ting RCA cables, make sure to match the color coded pins to the appropriate jacks on the
component being used as a source.
5.
Once all the speakers and audio components have been properly connected, plug the AC cord
of the speaker system into a wall outlet.
6.
Turn on the speaker by setting the main power switch on the back of the unit to its ON
position. After that, the user can also press the red standby button on the remote control to
toggle between active and standby modes.
7.
Select the input mode by pressing the source selector button located on the front of the main
unit or by using the corresponding input buttons on the remote control. The available modes are:
USB: enables audio playback from compatible files stored in a USB memory stick
SD: enables audio playback from compatible files stored in a SD memory card
: enables the streaming of audio wirelessly from compatible Bluetooth
Bluetooth
®
Aux: enables audio playback from devices fitted with an auxiliary 3.5mm jack.
DVD: additional input enables the connection of audio components with full 5.1 channel
capability.
Tuner: allows you to listen to active channels in the band.
Note: please remember that some commands will not be active or behave differently in
both line in modes (refer to the product diagram for details).
8.
Using the controls on the front of the main unit or the remote, you can manage and select
your tracks, mute the speaker audio, in addition to adjusting the the output levels of each
channel individually.
9.
If you do not intend to use the speakers for a long time, set the power switch back to its
OFF position.
VI. Advanced operation
Note: Before installing this product, please make sure your device is compatible with Bluetooth
Pairing the speaker with your wireless device
1.
Place both devices not more than one meter away from each other.
2.
Enable the Bluetooth
function on your device and set it to discover the KWS-751 wireless
®
speaker.
3.
On the speaker, press the Source button to select the Bluetooth
appears on the screen. Alternatively you may use the remote to enable the Bluetooth
feature.
4.
At this point, two short beeps will be generated, making the red dot on the display to start
blinking fast. This indicates that the system has entered into the pairing mode.
5.
Once the speaker is listed under the newly found Bluetooth
Yes or OK. If you have a lower Bluetooth
passkey 0000 (4 zeros).
6.
If pairing is successful, another short beep will be heard, making the dot on the LED change
to steady red on the speaker screen. On your device, a message will be displayed, confir-
ming that the connection has been established.
7.
If after 60 seconds the pairing process fails, please repeat steps 1 through 5 described
above.
8.
From then on, your device will be automatically paired with the speaker.
VII. Multichannel surround setup
In order to get the best performance from your audio system, the optimum location for the
speakers needs to be determined.
Most DVDs and many streaming sources come with a 5.1 channel format, which is fully
supported by this system.
devices
®
Note:
PRO-LOGIC must be ON to experience the full 5.1CH setup.
To check if PRO-LOGIC is enabled, press the button on the remote or subwoofer. The
display will show PL.ON when the function is activated.
.
®
mode as soon as it
®
devices, accept by pressing
®
version, you may be prompted to enter the
®
Surround sound experience
Seating position
®
Publicidad
Tabla de contenido
