General Instructions; Qualified People; Safety Instructions; Standards - WEG G Serie Manual De Instalación, Operación Y Mantenimiento

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

2

GENERAL INSTRUCTIONS

Professionals who work with electrical installations, either in assembly, operation or maintenance, should be continuously
updated and be informed about rules and safety regulations governing the service and are advised to observe them strictly.
Before the initiation of any work, the responsible person must ensure that everything was properly noticed and alert
operators to the dangers inherent in the task to be performed. Alternators of this type, if used improperly or receive poor
maintenance, or when people do not receive the intervention of not qualified personnel may cause serious personal injury
and/or material damage. It is therefore recommended that these services be always performed by qualified people.

2.1 QUALIFIED PEOPLE

It is understood by people qualified those professionals
who, because of their training, experience, education level,
knowledge of relevant standards, specifications, safety
standards, accident prevention and knowledge of
operating conditions, have been authorized by their
leaders to carry out the work required and that can
recognize and avoid potential danger.
These qualified people must also know the first aid
procedures and be able to provide such service if
necessary.
It is assumed that all work of commissioning, maintenance
and repairs are done only by qualified people.

2.2 SAFETY INSTRUCTIONS

DANGER
During operation, these devices have
exposed energized or rotating parts, which
may have high voltage or high temperature.
Thus the operation with open terminal boxes,
unprotected couplings, or incorrect handling
without considering the standards of
operation may cause serious injury and
property damage.
Those responsible for safety of the facility must ensure that:
Only qualified people perform installation and operation
of equipment;
These people have this manual and other documents
provided with the alternator, as well as perform the
work strictly observing the instructions of service,
relevant standards and documentation of specific
products.
Failure to comply with installation standards and safety
may void the warranty.
Equipment for firefighting and first aid notices should be at
work in clearly visible and easily accessible places.
Please also notice:
All technical data about the applications permitted
(operating conditions, connections and installation
environment) contained in the catalog, documentation
of the application, operating instructions, manuals and
other documents;
The specific determinations and conditions to the
installation site;
The use of tools and equipment suitable for handling
and transport;
That protective devices of the individual components be
removed before installation.
The individual parts must be stored in an environment free
of vibrations, preventing falls and ensuring that they are
protected against aggressive and / or endanger the safety
of people.
10680382
Installation, operation and maintenance manual – Synchronous Alternator – G line - Horizontal

2.3 STANDARDS

Alternators are specified, designed, manufactured and
tested according to the following standards:
Table 2.1: Applicable standards
Specification
60034-1
Dimensions
Tests
60034-4
Protection degrees
60034-5
Cooling
60034-6
Mounting
60034-7
Noise
60034-14

2.4 ENVIRONMENT FEATURES

In accordance with IEC 60034.1, and ABNT 5117, the
ambient operating conditions for which the alternators
were designed are the following:
1. Ambient temperature: – 15 ºC to + 40 ºC;
2. Altitude (sea level): up to 1000 m;
3. Environment without the presence of aggressive
agents such as: salt spray, chemicals, etc.;
4. Environment according to the protection degree of the
alternator.
Special conditions of environment are described on the
rating plate and specific technical data sheet of the
alternator.
ATTENTION
For use of alternators with water cooling at
temperatures below 0 °C, antifreeze additives
must be added in water.
www.weg.net
IEC
NBR
ISO
5117
60072
5432
5052
9884
5110
5031
5117
8528
l 15

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

GtaGtfGtwGtkGpaGpf ... Mostrar todo

Tabla de contenido